A novel polyimide (PI) and imide compound emitting prominent reddish-orange fluorescence under excitation by UV light were prepared based on 3-hydroxypyromellitic dianhydride (PHDA), and their fluorescence properties were examined. The steady-state fluorescence spectrum of a PI film displayed an emission band at 590 nm with a very large Stokes shift (ν = 10 448 cm −1 ) via the excited-state intramolecular proton transfer (ESIPT), while the time-resolved fluorescence spectrum showed a rapid decay of the emission band of the enol form at around 400 nm within 15 ps. Transient absorption measurements showed an induced absorption and stimulated emission of the keto form with a time constant of ca. 3.0 ps, implying that ESIPT occurs on this time scale. Consequently, introduction of a hydroxy group into the pyromellitic moiety of PIs and imide compounds led to the long-wavelength ESIPT emission applicable to spectral converters having high thermal, mechanical, and environmental stabilities.

Plasmonic metal nanoparticles arranged in periodic arrays can generate surface lattice plasmon resonances (SLRs) with high Q-factors. These collective resonances are interesting because the associated electromagnetic field is delocalized throughout the plane of the array, enabling applications such as biosensing and nanolasing. In most cases such periodic nanostructures are created via top-down nanofabrication processes. Here we describe a capillary-force-assisted particle assembly method (CAPA) to assemble monodisperse single-crystal colloidal Ag cuboctahedra into nearly defect-free >1 cm2 hexagonal lattices. These arrays are large enough to be measured with conventional ultraviolet–visible spectroscopy, which revealed an extinction peak with a Q-factor of 30 at orthogonal illumination and up to 80 at oblique illumination angles. We explain how the experimental extinction changes with different light polarizations and angles of incidence, and compare the evolution of the peaks with computational models based on the coupled dipole approximation and the finite element method. These arrays can support high Q-factors even when exposed to air, because of the high aspect ratio of the single-crystal nanoparticles. The observation of SLRs in a self-assembled system demonstrates that a high level of long-range positional control can be achieved at the single-particle level.

In this work we present an overview on structure formation, optical and electrical properties of diamond like carbon (DLC) based metal nanocomposites deposited by reactive magnetron sputtering and treated by plasma and laser ablation methods. The influence of deposition mode and other technological conditions on the properties of the nanosized filler, matrix components and composition were studied systematically in relation to the final properties of the nanocomposites. Applications of the nanocomposites in the development of novel biosensors combining resonance response of wave guiding structures in DLC based nanocomposites as well as plasmonic effects are also presented.

In the current work, a new antibacterial bandage was proposed where diamond-like carbon with silver nanoparticle (DLC:Ag)-coated synthetic silk tissue was used as a building block. The DLC:Ag structure, the dimensions of nanoparticles, the silver concentration and the silver ion release were studied systematically employing scanning electron microscopy, energy dispersive X-ray spectroscopy and atomic absorption spectroscopy, respectively. Antimicrobial properties were investigated using microbiological tests (disk diffusion method and spread-plate technique). The DLC:Ag layer was stabilized on the surface of the bandage using a thin layer of medical grade gelatin and cellulose. Four different strains of Staphylococcus aureus extracted from humans’ and animals’ infected wounds were used. It is demonstrated that the efficiency of the Ag+ ion release to the aqueous media can be increased by further RF oxygen plasma etching of the nanocomposite. It was obtained that the best antibacterial properties were demonstrated by the plasma-processed DLC:Ag layer having a 3.12 at % Ag surface concentration with the dominating linear dimensions of nanoparticles being 23.7 nm. An extra protective layer made from cellulose and gelatin with agar contributed to the accumulation and efficient release of silver ions to the aqueous media, increasing bandage antimicrobial efficiency up to 50% as compared to the single DLC:Ag layer on textile.

We present Raman studies of graphene films grown on copper foil by atmospheric pressure CVD with n-decane as a precursor, a mixture of nitrogen and hydrogen as the carrier gas, under different hydrogen flow rates. A novel approach for the processing of the Raman spectroscopy data was employed. It was found that in particular cases, the various parameters of the Raman spectra can be assigned to fractions of the films with different thicknesses. In particular, such quantities as the full width at half maximum of the 2D peak and the position of the 2D graphene band were successfully applied for the elaborated approach. Both the G- and 2D-band positions of single layer fractions were blue-shifted, which could be associated with the nitrogen doping of studied films. The XPS study revealed the characteristics of incorporated nitrogen, which was found to have a binding energy around 402 eV. Moreover, based on the statistical analysis of spectral parameters and the observation of a G-resonance, the twisted nature of the double-layer fraction of graphene grown with a lower hydrogen feeding rate was demonstrated. The impact of the varied hydrogen flow rate on the structural properties of graphene and the nitrogen concentration is also discussed.