Reduction in CO 2 emissions is strongly linked with the improvement of engine specific fuel consumption, as well as the reduction in engine nacelle drag and weight. Conventional turbofan designs, however, that reduce CO 2 emissions-such as increased overall pressure ratio designs-can increase the production of NO x emissions. In the present work, funded by the European Framework 6 collaborative project NEW Aero engine Core concepts (NEWAC), an aero-engine multidisciplinary design tool, Techno-economic, Environmental, and Risk Assessment for 2020 (TERA2020), has been utilized to study the potential benefits from introducing heat-exchanged cores in future turbofan engine designs. The tool comprises of various modules covering a wide range of disciplines: engine performance, engine aerodynamic and mechanical design, aircraft design and performance, emissions prediction and environmental impact, engine and airframe noise, as well as production, maintenance and direct operating costs. Fundamental performance differences between heat-exchanged cores and a conventional core are discussed and quantified. Cycle limitations imposed by mechanical considerations, operational limitations and emissions legislation are also discussed. The research work presented in this paper concludes with a full assessment at aircraft system level that reveals the significant potential performance benefits for the intercooled and intercooled recuperated cycles. An intercooled core can be designed for a significantly higher overall pressure ratio and with reduced cooling air requirements, providing a higher thermal efficiency than could otherwise be practically achieved with a conventional core. Variable geometry can be implemented to optimize the use of the intercooler for a given flight mission. An intercooled recuperated core can provide high thermal efficiency at low overall pressure ratio values and also benefit significantly from the introduction of a variable geometry low pressure turbine. The necessity of introducing novel lean-burn combustion technology to reduce NO x emissions at cruise as well as for the landing and take-off cycle, is demonstrated for both heat-exchanged cores and conventional designs. Significant benefits in terms of NO x reduction are predicted from the introduction of a variable geometry low pressure turbine in an intercooled core with lean-burn combustion technology.

Aviation is an important contributor to the global economy, satisfying society’s mobility needs. It contributes to climate change through CO2 and non-CO2 effects, including contrail-cirrus and ozone formation. There is currently significant interest in policies, regulations and research aiming to reduce aviation’s climate impact. Here we model the effect of these measures on global warming and perform a bottom-up analysis of potential technical improvements, challenging the assumptions of the targets for the sector with a number of scenarios up to 2100. We show that although the emissions targets for aviation are in line with the overall goals of the Paris Agreement, there is a high likelihood that the climate impact of aviation will not meet these goals. Our assessment includes feasible technological advancements and the availability of sustainable aviation fuels. This conclusion is robust for several COVID-19 recovery scenarios, including changes in travel behaviour.

Key results from the EU H2020 project CENTRELINE are presented. The research activities undertaken to demonstrate the proof of concept (technology readiness level—TRL 3) for the so-called propulsive fuselage concept (PFC) for fuselage wake-filling propulsion integration are discussed. The technology application case in the wide-body market segment is motivated. The developed performance bookkeeping scheme for fuselage boundary layer ingestion (BLI) propulsion integration is reviewed. The results of the 2D aerodynamic shape optimization for the bare PFC configuration are presented. Key findings from the high-fidelity aero-numerical simulation and aerodynamic validation testing, i.e., the overall aircraft wind tunnel and the BLI fan rig test campaigns, are discussed. The design results for the architectural concept, systems integration and electric machinery pre-design for the fuselage fan turbo-electric power train are summarized. The design and performance implications on the main power plants are analyzed. Conceptual design solutions for the mechanical and aero-structural integration of the BLI propulsive device are introduced. Key heuristics deduced for PFC conceptual aircraft design are presented. Assessments of fuel burn, NOx emissions, and noise are presented for the PFC aircraft and benchmarked against advanced conventional technology for an entry-into-service in 2035. The PFC design mission fuel benefit based on 2D optimized PFC aero-shaping is 4.7%.

In this multidisciplinary study a geared open rotor configuration is assessed and compared to an ultra high bypass ratio geared turbofan engine. Both designs assume a 2020 entry into service level of technology. The specific thrust level for minimizing block fuel and the resulting engine emissions for a given mission is sought. The tool used contains models that effectively capture: engine performance, mechanical and aerodynamic design, engine weight, emissions, aircraft design and performance as well as direct operating costs. The choice of specific thrust is a complex optimization problem and several disciplines need to be considered simultaneously. It will be demonstrated, through multidisciplinary analysis, that the open rotor concept can offer a substantial fuel saving potential, compared to ducted fans, for a given set of design considerations and customer requirements.

No abstract

Although the benefits of intercooling for aero engine applications have been realized and discussed in many publications, quantitative details are still relatively limited. In order to strengthen the understanding of aero engine intercooling, detailed performance data on optimized intercooled turbofan engines are provided. Analysis is conducted using an exergy breakdown, i.e. quantifying the losses into a common currency by applying a combined use of the first and second law of thermodynamics. Optimal intercooled geared turbofan engines for a long range mission are established with CFD based two-pass cross flow tubular intercooler correlations. By means of a separate variable nozzle, the amount of intercooler coolant air can be optimized to different flight conditions. Exergy analysis is used to assess how irreversibility is varying over the flight mission, allowing for a more clear explanation and interpretation of the benefits. The optimal intercooled geared turbofan engine provides a 4.5% fuel burn benefit over a non-intercooled geared reference engine. The optimum is constrained by the last stage compressor blade height. To further explore the potential of intercooling the constraint limiting the axial compressor last stage blade height is relaxed by introducing an axial radial high pressure compressor. The axial-radial high pressure ratio configuration allows for an ultra-high overall pressure ratio. With an optimal top-of-climb overall pressure ratio of 140, the configuration provides a 5.3% fuel burn benefit over the geared reference engine. The irreversibilities of the intercooler are broken down into its components to analyze the difference between the ultra-high overall pressure ratio axial-radial configuration and the purely axial configuration. An intercooler conceptual design method is used to predict pressure loss heat transfer and weight for the different overall pressure ratios. Exergy analysis combined with results from the intercooler and engine conceptual design are used to support the conclusion that the optimal pressure ratio split exponent stays relatively independent of the overall engine pressure ratio.

The reduction of CO2 emissions is strongly linked with the improvement of engine specific fuel consumption, along with the reduction of engine nacelle drag and weight. One alternative design approach to improving specific fuel consumption is to consider a geared fan combined with an increased overall pressure ratio intercooled core performance cycle. The thermal benefits from intercooling have been well documented in the literature. Nevertheless, there is very little information available in the public domain with respect to design space exploration of such an engine concept when combined with a geared fan. The present work uses a multidisciplinary conceptual design tool to analyze the option of an intercooled core geared fan aero engine for long haul applications with a 2020 entry into service technology level assumption. With minimum mission fuel in mind, the results indicate as optimal values a pressure ratio split exponent of 0.38 and an intercooler mass flow ratio of 1.18 at hot-day top of climb conditions. At ISA midcruise conditions a specific thrust of 86 m/s, a jet velocity ratio of 0.83, an intercooler effectiveness of 56%, and an overall pressure ratio value of 76 are likely to be a good choice. A 70,000 lbf intercooled turbofan engine is large enough to make efficient use of an all-axial compression system, particularly within a geared fan configuration, but intercooling is perhaps more likely to be applied to even larger engines. The proposed optimal jet velocity ratio is actually higher than the value one would expect by using standard analytical expressions, primarily because this design variable affects core efficiency at mid-cruise due to a combination of several different subtle changes to the core cycle and core component efficiencies at this condition. The analytical expressions do not consider changes in core efficiency and the beneficial effect of intercooling on transfer efficiency, nor do they account for losses in the bypass duct and jet pipe, while a relatively detailed engine performance model, such as the one utilized in this study, does. Mission fuel results from a surrogate model are in good agreement with the results obtained from a rubberized-wing aircraft model for some of the design parameters. This indicates that it is possible to replace an aircraft model with specific fuel consumption and weight penalty exchange rates. Nevertheless, drag count exchange rates have to be utilized to properly assess changes in mission fuel for those design parameters that affect nacelle diameter.

This paper presents the study of a mid-sized semi-closed oxy-fuel combustion combined cycle (SCOC-CC) with net power output around 108 MW. The paper describes not only the power balance and the performance of the SCOC-CC, but also the conceptual design of the SCOC turbine and compressor. A model has been built in the commercial heat and mass balance code IPSEpro to estimate the efficiency of semi-closed dual-pressure oxy-fuel combustion combined cycle using natural gas as a fuel. In order to obtain the real physical properties of the working fluids in IPSEpro, the code was linked to the NIST Reference Fluid Thermodynamic and Transport Properties Database (REFPROP). The oxy-fuel turbine was modeled with the in-house Lund University package LUAX-T. Important features such as stage loading, loss modeling, cooling and geometric features were included to generate more accurate results. The oxy-fuel compressor has been modeled using a Chalmers university in-house tool for conceptual design of axial compressors. The conceptual design of the SCOC-CC process has a net efficiency of 47%. The air separation unit and CO2 compression reduce the cycle efficiency by 10 and 2 percentage points, respectively. A single-shaft configuration was selected for the gas turbine simplicity. The rotational speed chosen was 5200 rpm and the turbine was designed with four stages. All stage preliminary design parameters are within ranges of established industrial axial turbine design limits. The main issue is the turbine exit Mach number; the stage must be lightly loaded in terms of pressure ratio to maintain the exit Mach number below 0.6. The compressor is designed with 18 stages. The current value of the product of the annulus area and the blade rotational speed squared (AN2) was calculated and found to be 40·106.