The rheological properties of aqueous suspensions based on three different nanocelluloses were compared. One system was obtained via acid hydrolysis (thus yielding crystalline nanocellulose, CNC) and the other two from mechanical shearing, but from different origins and subjected to different pretreatments. Of the latter two, one was considered to be a rather typical cellulose nanofibril (CNF) suspension whereas the other was a kind of intermediate between CNF and CNC. All three nanocellulose elements differed in dimensions as evident from transmission electron microscopy and atomic force microscopy. With regard to the length of the fibrils/particles, the three nanocelluloses formed three distinct groups with lengths between 200 and slightly more than 800 nm. The three cellulosic elements were also subjected to a TEMPO-mediated oxidation yielding a similar carboxylate content in the three systems. Furthermore, the TEMPO-oxidized elements were grafted with poly(ethylene glycol) (PEG). The amount of grafted PEG was about 35 wt%. The shear viscosity, the storage modulus and the loss modulus of suspensions of the unmodified, the TEMPO-oxidized and the grafted nanocelluloses were determined at room temperature and the solids content of the suspensions was varied between 0.7 and 2.0 wt%. It was concluded that the rheological properties varied significantly between the suspensions depending on the dimensions of the cellulosic elements and their surface characteristics. In this context, the length (or the aspect ratio) of the particles played a very important role.
Cellulose nanocrystals (CNC) were surface modified by grafting azetidinium salts onto the sulphate ester groups on the cellulosic surfaces. The modified CNC were characterized using NMR, FTIR spectroscopy, conductometric titration and measurement of the f-potential. Thermal gravimetrical analysis revealed that the onset temperature for the thermal degradation was shifted upwards by almost 100°C as a result of the surface grafting. The rheological properties of dispersions based on unmodified and modified CNC were evaluated in detail. Two solids contents were studied; 0.65 and 1.3 wt%. In general, the grafting of the salts significantly increased the shear viscosity at a given shear rate as well as the storage and loss moduli of the dispersions. The CNC concentration at the gel point (network formation) decreased in a corresponding manner when the nanocellulosic particles were surface modified. This may be associated with pronounced hydrophobic attractive interactions between the grafted substituents.
In order to explore the reinforcing capabilities of cellulose nanofibrils, composites containing high contents of cellulose nanofibrils were prepared through a combination of water-assisted mixing and compression moulding, the components being a cellulose nanofibril suspension and an aqueous dispersion of the polyolefin copolymer poly(ethylene-co-acrylic acid). The composite samples had dry cellulose nanofibril contents from 10 to 70 vol%. Computed tomography revealed well dispersed cellulose fibril/fibres in the polymer matrix. The highest content of 70 vol% cellulose nanofibrils increased the strength and stiffness of the composites by factors of 3.5 and 21, respectively, while maintaining an elongation at break of about 5%. The strength and strain-at-break of cellulose nanofibril composites were superior to the pulp composites at cellulose contents greater than 20 vol%. The stiffness of the composites reinforced with cellulose nanofibrils was not higher than for that of composites reinforced with cellulose pulp fibres.
Composite fibres with a matrix of poly(ethylene glycol) (PEG) and cellulose nanofibrils (CNF) as reinforcing elements were produced using a capillary viscometer. Two types of CNF were employed: one based on carboxymethylated pulp fibres and the other on TEMPO-oxidized pulp. Part of the latter nanofibrils was also grafted with PEG in order to improve the compatibility between the CNF and the PEG matrix. The nominal CNF-content was kept at 10 or 30 weight-%. The composite fibres were characterized by optical and scanning electron microscopy in addition to dynamic mechanical thermal analysis (DMTA). Evaluation of the storage modulus indicated a clear reinforcing effect of the CNF, more pronounced in the case of the grafted CNF and depending on the amount of CNF. An interesting feature observed during the DMTA-measurements was that the fibrils within the composite fibres appeared to form a rather coherent and load-bearing network which was evident even after removing of the PEG-phase (by melting). An analysis of the modulus of the composite fibres using a rather simple model indicated that the CNF were more efficient as reinforcing elements at lower concentrations which may be associated with a more pronounced aggregation as the volume fraction of CNF increased.
Broad-band dielectric spectroscopy is a commonly used tool in the study of glass-forming liquids. The high sensitivity of the technique together with the wide range of probed time scales makes it a powerful method for investigating the relaxation spectra of liquids. One particularly important class of glass-forming liquids that is often studied using this technique consists of liquids dominated by hydrogen (H) bond interactions. When investigating such liquids, particular caution has to be taken during sample preparation due to their often highly hygroscopic nature. Water can easily be absorbed from the atmosphere, and dielectric spectroscopy is a very sensitive probe of such contamination due to the large dipole moment of water. Our knowledge concerning the effects of small quantities of water on the dielectric properties of these commonly investigated liquids is limited. We here demonstrate the effects due to the presence of small amounts of water on the dielectric response of a typical H-bonded model glass former, tripropylene glycol. We show how the relaxation processes present in the pure liquid are affected by addition of water, and we find that a characteristic water induced relaxation response is observed for water contents as low as 0.15 wt%. We stress the importance of careful purification of hygroscopic liquids before experiments and quantify what the effects are if such procedures are not undertaken.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.