The rheological properties of aqueous suspensions based on three different nanocelluloses were compared. One system was obtained via acid hydrolysis (thus yielding crystalline nanocellulose, CNC) and the other two from mechanical shearing, but from different origins and subjected to different pretreatments. Of the latter two, one was considered to be a rather typical cellulose nanofibril (CNF) suspension whereas the other was a kind of intermediate between CNF and CNC. All three nanocellulose elements differed in dimensions as evident from transmission electron microscopy and atomic force microscopy. With regard to the length of the fibrils/particles, the three nanocelluloses formed three distinct groups with lengths between 200 and slightly more than 800 nm. The three cellulosic elements were also subjected to a TEMPO-mediated oxidation yielding a similar carboxylate content in the three systems. Furthermore, the TEMPO-oxidized elements were grafted with poly(ethylene glycol) (PEG). The amount of grafted PEG was about 35 wt%. The shear viscosity, the storage modulus and the loss modulus of suspensions of the unmodified, the TEMPO-oxidized and the grafted nanocelluloses were determined at room temperature and the solids content of the suspensions was varied between 0.7 and 2.0 wt%. It was concluded that the rheological properties varied significantly between the suspensions depending on the dimensions of the cellulosic elements and their surface characteristics. In this context, the length (or the aspect ratio) of the particles played a very important role.

Cellulose nanocrystals (CNC) were surface modified by grafting azetidinium salts onto the sulphate ester groups on the cellulosic surfaces. The modified CNC were characterized using NMR, FTIR spectroscopy, conductometric titration and measurement of the f-potential. Thermal gravimetrical analysis revealed that the onset temperature for the thermal degradation was shifted upwards by almost 100°C as a result of the surface grafting. The rheological properties of dispersions based on unmodified and modified CNC were evaluated in detail. Two solids contents were studied; 0.65 and 1.3 wt%. In general, the grafting of the salts significantly increased the shear viscosity at a given shear rate as well as the storage and loss moduli of the dispersions. The CNC concentration at the gel point (network formation) decreased in a corresponding manner when the nanocellulosic particles were surface modified. This may be associated with pronounced hydrophobic attractive interactions between the grafted substituents.

Cellulose nanocrystals (CNCs) prepared via sulfuric acid hydrolysis are decorated with sulfate groups that yield a stable water suspension. To make the CNCs adaptable for use in composites, the hydroxyl groups on the surface are usually hydrophobized. In this article, an alternative hydrophobization method is described in which the sulfate groups are conjugated with azetidinium salts. The results of this study show that the sulfate groups can be functionalized with azetidinium salts and from thermal studies, it was discovered that the functionalization led to a 100 8C increase in thermal stability, compared with unmodified CNCs. The nanocomposites prepared by extrusion of CNC-coated low-density polyethylene powder displayed similar mechanical properties as the CNC-reference sample, but without the discoloration, due to the increased thermal stability. In conclusion, the azetidinium reagent reacts preferentially with sulfate groups, and this new type of chemical conversion of sulfate groups on polysaccharides will be beneficial in nanocomposite manufacturing.

One of the main challenges for industrial production of cellulose nanocrystals is the high energy demand during the dewatering of dilute aqueous suspensions. It is addressed in this study by utilising electroosmotic dewatering to increase the solid content of suspensions of cellulose nanocrystals. The solid content was increased from 2.3 up to 15.3 wt%, i.e. removal of more than 85% of all the water present in the system, at a much lower energy demand than that of thermal drying. Increasing the strength of the electric field increased not only the dewatering rate but also the specific energy demand of the dewatering operation: the electric field strength used in potential industrial applications is thus a trade-off between the rate of dewatering and the energy demand. Additionally, it was found that high local current intensity had the potential of degrading cellulose nanocrystals in contact with the anode. The maximum strength of the electric field applied should therefore be limited depending on the equipment design and the suspension conditions.