No abstract

S. Confocal scanning laser microscopy (CSLM) methods were developed to identify fat and protein in cheeses, milk chocolate and milk powders. Various fluorescent probes were assessed for their ability to label fat or protein in selected food products in situ. Dual labelling of fat and protein was made possible by using mixtures of probes. Selected probes and probe mixtures were then used to study (a) structure development of Mozzarella cheese during manufacture and ripening, and (b) the distribution of fat and protein in milk chocolate made with milk powders containing varying levels of free fat. Microstructural changes in the protein and fat phases of Mozzarella cheese were observed at each major step in processing. Aggregation of renneted micelles occurred during curd formation ; this was followed by amalgamation of the para-casein into linear fibres during plasticization. Following storage, the protein phase of the Mozzarella became more continuous ; entrapping and isolating fat globules. Chocolate made with a high free-fat spray-dried powder blend showed a homogeneous fat distribution, similar to that of chocolate made with roller-dried milk. Chocolate made with whole milk powder containing 10 g free fat\100 g fat showed a non-homogeneous fat distribution with some fat occluded within milk protein particles. These differences in fat distribution were related to Casson yield value and Casson viscosity of the chocolates.

The influence of feeding system and lactation period on the gross composition, macroelements (Ca, P, Mg, and Na), and trace elements (Zn, Fe, Cu, Mo, Mn, Se, and Co) of bovine milk was investigated. The feeding systems included outdoor grazing on perennial ryegrass pasture (GRO), outdoor grazing on perennial ryegrass and white clover pasture (GRC), and indoors offered total mixed ration (TMR). Sixty spring-calving Holstein Friesian dairy cows were assigned to 3 herds, each consisting of 20 cows, and balanced with respect to parity, calving date, and pre-experimental milk yield and milk solids yield. The herds were allocated to 1 of the 3 feeding systems from February to November. Milk samples were collected on 10 occasions over the period June 17 to November 26, at 2 or 3 weekly intervals, when cows were on average 119 to 281 d in lactation (DIL). The total lactation period was arbitrarily sub-divided into 2 lactation periods based on DIL, namely mid lactation, June 17 to September 9 when cows were 119 to 203 DIL; and late lactation, September 22 to November 26 when cows were 216 to 281 DIL. With the exception of Mg, Na, Fe, Mo, and Co, all other variables were affected by feeding system. The GRO milk had the highest mean concentrations of total solids, total protein, casein, Ca, and P. The TMR milk had the highest concentrations of lactose, Cu, and Se, and lowest level of total protein. The GRC milk had levels of lactose, Zn, and Cu similar to those of GRO milk, and concentrations of TS, Ca, and P similar to those of TMR milk. Lactation period affected all variables, apart from the concentrations of Fe, Cu, Mn, and Se. On average, the proportion (%) of total Ca, P, Zn, Mn, or Se that sedimented with the casein on high-speed ultracentrifugation at 100,000 × g was ≥60%, whereas that of Na, Mg, or Mo was ≤45% total. The results demonstrate how the gross composition and elemental composition of milk can be affected by different feeding systems.

Dairy and cereal are frequently combined to create composite foods with enhanced nutritional benefits. Dehydrated fermented milk–wheat composites (FMWC) were prepared by blending fermented milk (FM) and parboiled wheat (W), incubating at 35 °C for 24 h, drying at 46 °C for 48 h, and milling to 1 mm. Increasing the weight ratio of FM to W from 1.5 to 4.0 resulted in reductions in total solids (from 96 to 92%) and starch (from 52 to 39%), and increases in protein (15.2–18.9%), fat (3.7–5.9%), lactose (6.4–11.4%), and lactic acid (2.7–4.2%). FMWC need to be reconstituted prior to consumption. The water-holding capacity, pasting viscosity, and setback viscosity of the reconstituted FMWC (16.7% total solids) decreased with the ratio of FM to W. The reconstituted FMWC exhibited pseudoplastic flow behaviour on shearing from 18 to 120 s−1. Increasing the FM:W ratio coincided with a lower yield stress, consistency index, and viscosity at 120 s−1. The results demonstrate the critical impact of the FM:W ratio on the composition, pasting behavior, and consistency of the reconstituted FMWC. The difference in consistency associated with varying the FM:W ratio is likely to impact on satiety and nutrient value of the FMWCs.

The growth in food service and prepared consumer foods has led to increasing demand for cheese with customized textural and cooking characteristics. The current study evaluated Kačkavalj, Kačkavalj Krstaš, and Trappist cheeses procured from manufacturing plants in Serbia for texture profile characteristics, flow and extensibility of the heated cheese, and changes in viscoelasticity characteristics during heating and cooling. Measured viscoelastic parameters included elastic modulus, G', loss modulus, G″, and loss tangent, LT (G″/G'). The melting temperature and congealing temperature were defined as the temperature at which LT=1 during heating from 25 to 90°C and on cooling from 90 to 25°C. The maximum LT during heating was as an index of the maximum fluidity of the molten cheese. Significant variation was noted for the extent of flow and extensibility of the heated cheeses, with no trend of cheese type. As a group, the Kačkavalj cheeses had relatively high levels of salt-in-moisture and pH 4.6-soluble N and low protein-to-fat ratio and levels of αs1-CN (f24-199). They fractured during compression to 75%; had relatively low values of cohesiveness, chewiness, and springiness; melted at ~70 to 90°C; reached maximum LT at 90°C; and congealed at 58 to 63°C. Conversely, the Kačkavalj Krstaš and Trappist cheeses had low levels of primary proteolysis and salt-in-moisture content and a high protein-to-fat ratio. They did not fracture during compression, had high values for cohesiveness and chewiness, melted at lower temperatures (56-62°C), attained maximum fluidity at a lower temperature (72-78°C), and congealed at 54 to 69°C. There was a hysteretic dependence of G' and LT on temperature for all cheeses, with the LT during cooling being higher than that during heating, and G' during cooling being lower or higher than the equivalent values during heating depending on the cheese type. Monitoring the dynamic changes in viscoelasticity during heating and cooling of the cheese in the temperature range 25 to 90°C provides a potentially useful means of designing ingredient cheeses, with the desired attributes when heated and cooled under customized specification.