No abstract

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. This is an author-deposited version published in: https://sam.ensam.eu Handle IDAbstract-The present paper deals with the post-fault synchronization of a voltage source converter based on the droop control. In case of large disturbances on the grid, the current is limited via current limitation algorithms such as the virtual impedance. During the fault, the power converter internal frequency deviates resulting in a converter angle divergence. Thereby, the system may lose the synchronism after fault clearing and which may lead to instability. Hence, this paper proposes a theoretical approach to explain the dynamic behavior of the grid forming converter subject to a three phase bolted fault. A literal expression of the critical clearing time is defined. Due to the precise analysis of the phenomenon, a simple algorithm can be derived to enhance the transient stability. It is based on adaptive gain included in the droop control. These objectives have been achieved with no external information and without switching from one control to the other. To prove the effectiveness of the developed control, experimental test cases have been performed in different faulted conditions.

Renewable generation is mainly connected through converters. Even if they provide more and more ancillary services to the grid, these may not be sufficient for extremely high penetrations. As the share of such generating units is growing rapidly, some synchronous areas could in the future occasionally be operated without synchronous machines. In such conditions, system behaviour will dramatically change, but stability will still have to be ensured with the same level of reliability as today. To reach this ambitious goal, the control of inverters will have to be changed radically. Inverters will need to move from following the grid to leading the grid behaviour, both in steady state and during transients. This new type of control brings additional issues on converters that are addressed in this study. A solution is proposed to allow a stable operation of the system together with a limited solicitation of inverters during transients.

This version is available at https://strathprints.strath.ac.uk/62151/ Strathprints is designed to allow users to access the research output of the University of Strathclyde. Unless otherwise explicitly stated on the manuscript, Copyright © and Moral Rights for the papers on this site are retained by the individual authors and/or other copyright owners. Please check the manuscript for details of any other licences that may have been applied. You may not engage in further distribution of the material for any profitmaking activities or any commercial gain. You may freely distribute both the url (https://strathprints.strath.ac.uk/) and the content of this paper for research or private study, educational, or not-for-profit purposes without prior permission or charge.Any correspondence concerning this service should be sent to the Strathprints administrator: strathprints@strath.ac.ukThe Strathprints institutional repository (https://strathprints.strath.ac.uk) is a digital archive of University of Strathclyde research outputs. It has been developed to disseminate open access research outputs, expose data about those outputs, and enable the management and persistent access to Strathclyde's intellectual output.

From the origin of the grid, energy has been delivered to electrical loads mainly by synchronous machines. All the main rules to manage the grid have been based on the electromechanical behavior of these machines which have been extensively studied for many years. Due to the increase of HVDC link and renewable energy sources as wind turbine and PV, power converters are massively introduced in the grid with a fundamentally different dynamic behavior. Some years ago, they were connected as simple power injector. Then, they were asked to provide some ancillary services to the grid, in the future, grid forming capability will be required. Even if gridforming converters had been extensively studied for microgrids and offshore grids, it has to be adapted to transmission grid where the topology may be largely modified. This paper presents an algorithm for calculating the controller parameters of a gridforming converter which guarantee a stable behavior for many different configurations of the grid.

Abstract-The subject of this paper is the investigation of the stability of a Voltage Source Converter (VSC) undergoing a sudden decrease of the Short Circuit Capacity of the AC system to which it is connected. A case study is reported on a simple system including an HVDC terminal and a Thévenin equivalent. First, a small-signal stability analysis is performed showing that the PLL-based vector control may become unstable at powers lower than the theoretical static stability limit. Dynamic simulations demonstrate that the stability limit may further decrease depending on the disturbance. The need for a fast instability detection method is highlighted.

No abstract

This paper presents a novel control scheme for exchange of frequency support between asynchronous AC systems through a High Voltage Direct Current link or grid. The proposed controller bears the spirit of an emergency scheme. Using only locally available measurements, each converter can identify emergency situations that could potentially lead to unacceptable frequency values. Then appropriate control actions are taken to restrain the frequency decline and prevent it from reaching the thresholds of load shedding relays. Inspired of Model Predictive Control, the method uses simplified models of the AC and DC sides of the converter, and can incorporate various constraints. The effectiveness of the method is demonstrated on a test system consisting of two asynchronous AC areas interconnected through a five-terminal HVDC grid.