The effect of the addition of microcrystalline cellulose nanofibers into linear segmented polyurethanes (SPU) was investigated. The polymers were synthesized with 4,4-methylene-bisphenyldiisocyanate (MDI) and poly (tetramethyleneglycol) (PTMG) with 1,4-butanediol (BD) as chain extender. The nanocrystals were introduced during the PU polymerization, which resulted in cellulose nanofibrils covalently linked to the polymer. The interactions between the cellulose nanofibrils and the matrix lead to interesting changes in the behavior of the PU, with the hard segment (HS) phase being more affected by these interactions. SPUs with different contents of HS were synthesized to better understand these effects (23 to 45 wt %). Thermal, thermo-mechanical and mechanical characterization of the nanocomposites were performed. In general, the nanocellulose favored the phase separation between the soft and hard domains generating an upward shift in the melting temperatures of the crystalline phases, an increase in the Young's modulus and a decrease in deformation at break.Comparison of the unfilled polymer responses and that of the nanocomposites showed that by increasing cellulose content, increased dynamic storage and tensile modulus as well as melting temperatures and enthalpy of melting of the soft domains can be achieved. Addition of cellulose during the polymerization essentially erased the potential shape memory behavior originally displayed by some of the SPU. However, a sample prepared by adding the cellulose nanocrystals after the reaction showed that the mechanical properties were still improved, while the shape memory behavior of the polymer was preserved.

Segmented polyurethanes exhibiting shape memory properties were modified by the addition of polyaniline (PANI)-coated cellulose nanofibrils (CNFs). The two-phase structure of the polymer is responsible for the material's ability to 'remember' and autonomously recover its original shape after being deformed in response to an external thermal stimulus. PANI was grown on the surface of the CNFs via in situ polymerization. Modified nanocrystals were added to the segmented polyurethane in concentrations ranging from 0 to 15 wt%. The changes in the material properties associated with the percolation of the coated fibrils appear at higher concentrations than previously observed for non-modified CNFs, which suggests that fibril agglomeration is occurring due to the PANI coating. The shape memory behavior of the composites is maintained at about the same level as that of the unfilled polyurethane only up to 4 wt% of fibrils. At higher concentrations, the rigidity of the nanofibrils as well as their interaction with the hard-segment phase and the increasing difficulty of dispersing them in the polymer collaborate to produce early breakage of the specimens when stretched at temperatures above the melting point of the soft segments.

The response of synthesized shape memory segmented polyurethanes (PUs) was affected by the addition of cellulose nanocrystals, as well as by the various conditions selected to carry out thermomechanical cyclic tests. The PUs were synthesized from an α-hydro-ω-hydroxy-poly(ethylene oxide), tolylene-2,4-diisocyanate and 1,4-butanediol as chain extender. Nanocomposites were prepared by mixing a suspension of cellulose nanocrystals in N,N-dimethylformamide with the thermoplastic PU dissolved in the same organic solvent. The thermal properties of the neat PU and resulting composites were examined using differential scanning calorimetry. It was found that cellulose addition increases the PU soft segment melting and crystallization temperatures and the degree of crystallinity of this phase. Shape memory behavior was studied using cyclic thermal tensile tests. Both neat PU and composites exhibit shape memory properties, with fixity and recovery values that depend on heating temperature, imposed deformation, deformation rate and nanofiller addition.

Multi-walled carbon nanotubes (CNTs) and cellulose nanofibers (CNFs) reinforced shape memory polyurethane (PU) composite fibers and films have been fabricated via extrusion and casting methods. Cellulose nanofibers were obtained through acid hydrolysis of microcrystalline cellulose. This treatment aided in achieving stable suspensions of cellulose crystals in dimethylformamide (DMF), for subsequent incorporation into the shape memory matrix. CNTs were covalent functionalized with carboxyl groups (CNT-COOH) and 4,4 0 -methylenebis (phenylisocyanate) (MDI) (CNT-MDI) to improve the dispersion efficiency between the CNT and the polyurethane. Significant improvement in tensile modulus and strength were achieved by incorporating both fillers up to 1 wt% without sacrificing the elongation at break. Electron microscopy was used to investigate the degree of dispersion and fracture surfaces of the composite fibers and films. The effects of the filler (type and concentration) on the degree of crystallinity and thermal properties of the hard and soft segments that form the PU sample were studied by calorimetry. Overall, results indicated that the homogeneous dispersion of nanotubes and cellulose throughout the PU matrix and the strong interfacial adhesion between nanotubes and/or cellulose and the matrix are responsible for the enhancement of mechanical and shape memory properties of the composites. POLYM. COMPOS., 32:455-463, 2011. ª