The purpose of this study was to investigate the blood flow/pressure relationship (linear or nonlinear) in the superficial femoral artery when seated, as well as to investigate blood flow changes with exercise using varying cuff pressures and a preexercise (PE) condition. The presence of venous outflow with occlusion at rest and exercise was also investigated. Methods: Twenty-three subjects visited the lab on 3 occasions. First to determine linearity of blood flow using 0% to 90% arterial occlusion pressure (AOP), and venous outflow at rest and during exercise with cuff inflated to 40% AOP. Subsequent visits compared blood flow between rest and PE conditions to determine average blood flow, heart rate, systolic and diastolic blood pressure changes in response to a blood flow-restricted (BFR) exercise protocol. Results: Blood flow/pressure relationship is nonlinear at the superficial femoral artery (p < 0.01). No significant differences in average blood flow, conductance or mean arterial pressure (MAP) were found between 30% to 80% AOP (p = 1.0 to .08). Blood flow is not significantly different between rest and PE groups (p = 0.49) although initial 40% AOP and 40% exercise arterial occlusion pressure (EAOP) values were different between rest and PE groups. (p < 0.01). Conclusion: The nonlinear relationship at the superficial femoral artery demonstrates higher cuff pressures are not necessary to reduce blood flow in BFR exercise of the lower extremity. Furthermore, PE or warm-up is not necessary prior to determining EAOP as it does not alter blood flow responses during BFR exercise. We found evidence of venous outflow above the cuff both at rest and during exercise at 40% AOP.

Image charge detection is the foundation of charge detection mass spectrometry (CDMS). The mass-to-charge ratio, m/z, of a highly charged ion or particle is determined by measuring the particle's charge and velocity. Charge is typically determined from a calibrated image charge signal, and the particle velocity is calculated using the peaks from the shaped signal as they relate to the particle position and time-of-flight through a detector of known length. Although much has been done to improve the charge accuracy in CDMS, little has been done to address the inconsistencies in the particle velocity measurements and the interpretation of peak position and effective electrode length. In this work, we combine SIMION ion trajectory software and the Shockley−Ramo theorem to accurately determine the effective electrode length, peak position, and shape of the signal peaks. Six model charge detector geometries were examined with this method and evaluated in laboratory experiments. Experimental results in all cases agreed with the simulations. Using a charge detector with multiple, 12.7 mm-long cylindrical electrodes, experimental velocities across and between electrodes agreed within 0.25% relative standard deviation (RSD) when this method was used to correct for effective electrode lengths, corresponding to an uncertainty in the effective electrode length of only 40 μm. For a detector with multiple electrodes and varied electrode spacing, experiments showed that the peak amplitude and shape vary with the geometry and with the particle path through the detector, whereas all peak areas agreed to within 2.3% RSD. For a charge detector made of two printed circuit boards, the velocities agreed within 0.44% RSD using the calculated effective electrode length.

We present a novel and thorough simulation technique to understand image charge generated from charged particles on a printed-circuit-board detector. We also describe a custom differential amplifier to exploit the near-differential input to improve the signal-to-noise-ratio of the measured image charge. The simulation technique analyzes how different parameters such as the position, velocity, and charge magnitude of a particle affect the image charge and the amplifier output. It also enables the designer to directly import signals into circuit simulation software to analyze the full signal conversion process from the image charge to the amplifier output. A novel measurement setup using a Venturi vacuum system injects single charged particles (with diameters in the 100 s of microns range) through a PCB detector containing patterned electrodes to verify our simulation technique and amplifier performance. The measured differential amplifier presented here exhibits a gain of 7.96 µV/e− and a single-pass noise floor of 1030 e−, which is about 13× lower than that of the referenced commercial amplifier. The amplifier also has the capability to reach a single-pass noise floor lower than 140 e−, which has been shown in Cadence simulation.

No abstract

No abstract