This paper introduces scaling-factor and design guidelines for shielded-capacitive power transfer (shielded-CPT) systems, offering a simplified design process, coupling-structure optimization, and consideration of safety. A novel scaling-factor-analysis method is proposed by determining the configuration of the coupling structure that improves system safety and increases operating efficiency while minimizing the gap between the shield and the coupler plate. The inductor-series resistance is also analyzed to study the loss efficiency in the shielded-CPT system. The relationship among the shield-coupler gap, distance between the couplers, conductive-plate size, and delivered power is examined and presented. The proposed method is validated by implementing the shielded-CPT system with hardware and the result suggests that the proposed method can be used to design shielded-CPT systems with scaling-factor and safety considerations.
A capacitive power transfer (CPT) system wirelessly transfers energy between coupling plates and performance issues related to CPT systems are resonance conditions, matching impedance, voltage stress, and power loss. A generalized circuit model is proposed for shielded capacitive power transfer (S-CPT) using an algebraic method. The proposed generalized S-CPT model is analyzed based on the symmetric and asymmetric configurations, and the relationship between the parameters of S-CPT is obtained with respect to the resonance condition, matching impedance, voltage stress, and efficiency. The best configuration of a symmetric S-CPT is recommended, and an asymmetric S-CPT is proposed based on the analysis results. Asymmetric-S-CPT hardware was constructed and demonstrated an operating frequency of 13.56 MHz. The hardware experimental result shows the validity and effectiveness of the proposed generalized model for designing S-CPT.
Grounding of electrical installation is primarily concern with ensuring safety. The main purpose of grounding is to channel the fault current straightly to earth. To produce a good grounding system, the value of earth resistance must be reduce as low as possible. Otherwise, current may flow through to those who touch the damage electrical equipment instead of flowing through grounding system. In this project, a variety diameter of copper rod and galvanized iron rod were installed to build grounding system. The aim of this project is to find if there exists significance difference in the value of resistance when different diameter and different type of rod were used. Single rod testing and parallel rod testing were performed with fall of potential method to measure the value of earth resistance. Result shows that different types of rod with different diameter size produce different resistivity value which also depends on installation technique and soil condition.
A common voltage-controlled oscillator (VCO) architecture used in the phase locked loop (PLL) is the ring oscillator (RO). RO consist of number of inverters cascaded together as the input of the first stage connected to the output of the last stage. It is important to design the RO to be work at desired frequency depend on application with low power consumption. This paper presents a review the performance evaluation of different delay cell topologies the implemented in the ring oscillator. The various topologies analyzed includes current starved delay cell, differential delay cell and current follower cell. Performance evaluation includes frequency range, frequency stability, phase noise and power consumption had been reviewed and comparison of different topologies has been discussed. It is observed that starved current delay cell have lower power consumption and the different of the frequency range is small as compared to other type of delay cell.
In this study, we propose a four-plate structure with two shielding plates to produce shielded capacitive power transfer (S-CPT) at an operating frequency of 6.78 MHz for a 10 W system. By eliminating the inductors at the secondary side to form an asymmetrical topology, an S-CPT system was developed with a class-E power amplifier. Using MATLAB software, analysis was performed to obtain the parameters in the S-CPT system regarding resonance and impedance matching, and the proposed coupler structure was investigated through electric field simulation. The shield plate voltage stability was also investigated by analysing both the simulation and hardware experiment results. A prototype of S-CPT was established to validate the analysis results and to demonstrate the voltage at the shield plate of the proposed coupler structure. The experimental results are in good agreement with the simulation results. The proposed S-CPT exhibits an AC–AC efficiency of 84%, with a 56% voltage ground stability reduction because of implementing a balun.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.