Sludge waste of deinking process as toxic and hazardous material from spesific source containing ABSTRAKLimbah sludge proses deinking sebagai B3 dari sumber spesifik karena mengandung logam Pb dari tinta yang larut dalam air limbah. Menurut Kep.Men. LH no. 33/2009 semua industri wajib melakukan pemulihan lahan tekontaminasi limbah B3. Oleh karena itu perlu dilakuan penelitian bioremediasi menggunakan mikroba konsorsium. Penelitian dilakukan dengan variasi waktu inkubasi dari 0 -60 hari dan jumlah inokulum 5%, 10%, dan 15% (v/w). Keberhasilan bioremediasi adalah mengubah logam aktif dalam tanah menjadi tidak aktif oleh aktifitas mikroba, dinyatakan dengan penurunan nilai koefisien distribusi fase tertukarkan dan peningkaan fase residual Pb. Mikroba konsorsium PG 65-06 (A) : PG 97-02 (B) : MR 1.12-05 (C) : A1 (D) dengan perbandingan 1:1:1:1 menghasilkan kondisi optimum untuk penambahan inokulum 10% dan waktu inkubasi 40 hari dengan penurunan koefisien distribusi fase tertukarkan Pb sebesar 21% yang semula 19,3 mg/kg menjadi 15,91 mg/kg dan peningkatan fase residual Pb sebesar 146% yang semula 7,77 mg/kg menjadi 17,00 mg/kg. Nilai germination index pada kisaran 84,3-136,7% yang berarti tanah tersebut sudah tidak bersifat toksik pada tanaman.Kata kunci : bioremediasi, tanah terkontaminasi, limbah deinking industri kertas, logam berat Pb
Industrial Plantation Forest of Acacia mangium for pulp industry in Indonesia has declined its productivity due to a decrease in the quality of soil on the second cycle and thereafter. Therefore, the alternative raw material for pulp has to be found as a substitute for Acacia mangium. Research on the various ages of Acacia crassicarpa (4; 5 and 6 years old) as the pulp raw material has been done. Pulp was prepared using the kraft process. The optimum cooking condition with target Kappa Number of 15 ± 1 was obtained at 20-22% active alkali, 30% sulfidity, temperature of 165ºC, liquor ratio 1:4 and H factor of 1300. Pulp was then bleached using ECF (Elemental Chlorine Free) process with the sequence of ODEDED and XDEDED. Results showed that pulp yield was high enough and meet the standard requirement according to SNI 6107:2009, Pulp Kraft Putih Kayudaun (LBKP). hollocellulose content of Acacia crassicarpa (79,99-80,87%) and α cellulose content (43,33-48,62%) were higher compared to those of Acacia mangium (<79% and <43%) respectively, while lignin and extractive contents were significantly low. It was found that Acacia crassicarpa of 5 years old resulted in better bleached kraft pulp compared to those of 4 and 6 years old. It is concluded that Acacia crassicarpa has a good prospect to be developed in Industrial Plantation Forest as raw material for pulp. Keywords: Acacia crassicarpa, ages, raw material, ECF, pulp ABSTRAK Hutan Tanaman Industri Acacia mangium untuk industri pulp yang dikembangkan di Indonesia saat ini mengalami penurunan produktivitas akibat penurunan kualitas tempat tumbuh pada daur kedua dan seterusnya. Oleh sebab itu perlu dicari bahan baku alternatif pengganti Acacia mangium. Untuk itu telah dilakukan penelitian terhadap Acacia crassicarpa berbagai umur yaitu 4 ; 5 dan 6 tahun. Pembuatan pulp kertas dilakukan dengan proses kraft. Kondisi pemasakan yang optimal dan memenuhi target bilangan Kappa 15 ± 1, diperoleh pada penggunaan alkali aktif 20-22%, sulfiditas 30%, suhu 165ºC, rasio 1:4 dan faktor H 1300. Pemutihan pulp dilakukan dengan proses ECF (Elemental Chlorine Free) yang dikenal ramah lingkungan dengan tahapan ODEDED dan XDEDED. Hasil pulp kraft putih mempunyai rendemen cukup tinggi dan memenuhi pesyaratan spesifikasi SNI 6107:2009, Pulp Kraft Putih Kayudaun (LBKP) kecuali indeks sobek. Kayu Acacia crassicarpa mempunyai kadar holoselulosa (79,99-80,87%) dan selulosa alfa (43,33-48,62%) yang cukup tinggi bila dibandingkan dengan Acacia mangium (<79% dan <43%), serta kadar lignin dan ekstraktif yang cukup rendah. Kayu Acacia crassicarpa umur 5 tahun menghasilkan pulp kraft putih paling baik dibandingkan umur 4 dan 6 tahun. Dengan demikian, kayu Acacia crassicarpa mempunyai potensi untuk dikembangkan di Hutan Tanaman Industri sebagai bahan baku pulp. Kata kunci: Acacia crassicarpa, umur, bahan baku, ECF, pulp
One effort to overcome the limited cotton is the use of dissolving pulp or rayon pulp with high α-cellulose content. The aim of this research is to study the nitration process of cellulose from various commercial dissolved pulp into nitrocellulose, which is a material for Propellant Nitro Cellulose (PNC). The most important parameter in the preparation of propellant is nitrogen level, which should be higher than 12,75%. The dissolving pulps from softwood sulfite process (A), hardwood kraft process (B), and hardwood sulfite process (C) were pre-treated before nitration process, namely ball mill, willey mill, and blender. Nitrocellulose was made using two types of formulas, which were formula one (HNO3:HNO3 Fumming:H2SO4 = 1:3:12) and formula two (HNO3:HNO3 Fumming:H2SO4 = 1:1.25:4). The results showed that the preparation of nitrocellulose from dissolving pulp A using blender pretreatment and formula two provided the highest nitrogen level (14.05%). The burn test of nitrocellulose met the smokeless specifications. Furthermore, the functional groups test by FTIR showed the presence of nitro group.Keywords: dissolving pulp, nitrocellulose, propellant, nitrogen content, nitration process ABSTRAK Salah satu upaya untuk mengatasi ketersediaan kapas yang terbatas adalah dengan menggunakan pulp larut atau pulp rayon yaitu pulp dengan kandungan α-selulosa yang tinggi. Penelitian ini bertujuan untuk mencari formula dan bahan baku yang paling baik untuk pembuatan nitroselulosa sebagai bahan Propellant Nitro Cellulose (PNC) dengan menggunakan berbagai jenis pulp larut komersial. Parameter yang terpenting dalam pembuatan propelan adalah kadar nitrogen harus lebih dari 12,75%. Sebelum proses nitrasi, dilakukan beberapa cara perlakuan awal yaitu menggunakan ballmill, willeymill, dan blender terhadap pulp larut dari jenis kayujarum proses sulfit (A), kayudaun proses kraft (B), dan kayudaun proses sulfit (C). Nitroselulosa dibuat menggunakan dua jenis formula yaitu formula 1 (HNO3:HNO3 Fumming:H2SO4= 1:3:12) dan formula 2 (HNO3:HNO3 Fumming:H2SO4= 1:1,25:4). Hasil penelitian menunjukkan bahwa pembuatan nitroselulosa dari pulp larut A dengan perlakuan awal blender dan menggunakan formula 2 memberikan kadar nitrogen yang paling besar yaitu sekitar 14,05%. Sedangkan uji nyala nitroselulosa memenuhi spesifikasi smokeless dan uji gugus fungsi dengan FTIR menunjukkan adanya gugus nitro.Kata kunci: pulp larut, nitroselulosa, propelan, kadar nitrogen, proses nitrasi
The use of xylanase in pulp bleaching process is intended to reduce chemicals consumption in pulp industry that still using chlorine compounds (chlorine dioxide), so the bleaching stage needs to be modified without reducing the quality of dissolving pulp. Dissolving pulp was produced from six-year-old Acacia crassicarpa as raw material by the Prehydrolysis-Kraft process, then the pulp was bleached with the ECF (elemental chlorine free) process using xylanase (X) and oxygen (O) as comparison at the early stage of bleaching. The sequences of process include X/ODEDED (xylanase or oxygen; chlorine dioxide; extraction-1; chlorine dioxide-1; extraction-2; chlorine dioxide -2). Results showed that the dissolving pulp with active alkali of 22%, sulphidity of 30%, the temperature of 165oC, and the ratio of 1:4 is the optimal condition. Cellulose content, viscosity and brightness were above 94%, 6.2 cP and 88% ISO, respectively.The dissolving pulp produced with the application of xylanase has better quality than the oxygen one, and meets the requirement according to Indonesia National Standard (SNI 0938:2010, pulp rayon).Keywords: Acacia crassicarpa, xylanase, Prehydrolysis-Kraft, dissolving pulp, rayon pulpABSTRAKPenggunaan xilanase pada proses pemutihan pulp dimaksudkan untuk mengurangi konsumsi bahan kimia yang digunakan selama ini di industri pulp, yang masih menggunakan senyawa klorin (klorin dioksida), untuk itu perlu dilakukan modifikasi pada tahap pemutihannya tanpa mengurangi kualitas dissolving pulp yang dihasilkan. Pembuatan dissolving pulp dilakukan menggunakan bahan baku kayu Acacia crassicarpa berumur 6 tahun dengan proses Prahidrolisa–Kraft, selanjutnya pulp diputihkan dengan proses ECF (Elemental Chlorine Free) menggunakan xilanase (X) dan oksigen (O) sebagai pembanding pada awal pemutihan dengan 6 tahapan proses, yaitu X/ODEDED (xilanase atau oksigen; klorin dioksida; ekstraksi-1; klorin dioksida-1; ekstraksi-2; klorin dioksida-2) dengan perlakuan oksigen sebagai pembanding. Hasil pembuatan dissolving pulp dengan alkali aktif 22%, sulfiditas 30%, suhu 165oC, rasio 1:4 adalah kondisi yang optimal. Kandungan selulosa, viskositas dan derajat cerah yang diperoleh masing-masing yaitu di atas 94%, 6,2 cP dan 88% ISO. Kualitas dissolving pulp hasil pemutihan dengan penambahan xilanase lebih tinggi daripada menggunakan oksigen dan memenuhi persyaratan spesifikasi SNI 0938:2010, pulp rayon. Kata kunci : Acacia crassicarpa, xilanase, Prahidrolisa-Kraft, dissolving pulp, pulp rayon
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.