Chitosan is a biopolymer that exhibits osteoconductive, enhanced wound healing and antimicrobial properties which make it attractive for use as a bioactive coating to improve osseointegration of orthopaedic and craniofacial implant devices. Coatings made from 91.2% de-acetylated chitosan were chemically bonded to titanium coupons via silane-glutaraldehyde molecules. The bond strength of the coatings was evaluated in mechanical tensile tests, and their dissolution and cytocompatibility were evaluated in vitro using cell-culture medium and UMR 106 osteoblastic cells, respectively. The results showed that the chitosan coatings were chemically bonded to the titanium substrate and that the bond strengths (1.5-1.8 MPa) were not affected by gas sterilization. However, the chitosan bond strengths were less than those reported for calcium-phosphate coatings. The gas-sterilized coatings exhibited little dissolution over 8 weeks in cell-culture solution, and the attachment and growth of the UMR 106 osteoblast cells was greater on the chitosan-coated samples than on the uncoated titanium. These results indicated that chitosan has the potential to be used as a biocompatible, bioactive coating for orthopaedic and craniofacial implant devices.

One of the most important factors in any tissue-engineering application is the cell substrate. The purpose of this study was the initial evaluation of chitosan, a derivative of the abundant, naturally occurring biopolymer chitin, as a cell scaffold for cartilage tissue engineering. Chitosan scaffolds having an interconnecting porous structure were easily fabricated by simple freezing and lyophilization of a chitosan solution. After rehydration of scaffolds, porcine chondrocytes were seeded onto scaffolds and cultured for up to 28 days in a rotating-wall bioreactor. Chitosan scaffolds supported cell attachment and maintenance of a rounded cell morphology. After 18 days, cells within the scaffolds had synthesized extracellular matrix in which proteoglycan and type II collagen were detected by toluidine blue staining and immunohistochemistry, respectively. Abundant extracellular matrix was found almost exclusively in the periphery of the scaffolds, as scaffold microstructure prevented cells from penetrating to interior regions. Nonetheless, the results suggest that chitosan scaffolds may be a useful alternative to synthetic cell scaffolds for cartilage tissue engineering.

Tissue engineered cardiac grafts are a promising therapeutic mode for ventricular wall reconstruction. Recently, it has been found that acellular tissue scaffolds provide natural ultrastructural, mechanical, and compositional cues for recellularization and tissue remodeling. We thus assess the potential of decellularized porcine myocardium as a scaffold for thick cardiac patch tissue engineering. Myocardial sections with 2 mm thickness were decellularized using 0.1% sodium dodecyl sulfate (SDS), and then reseeded with differentiated bone marrow mononuclear cells. We found that thorough decellularization could be achieved after 2.5 weeks treatment. Reseeded cells were found to infiltrate and proliferate in the tissue constructs. Immunohistological staining studies showed that the reseeded cells maintained cardiomyocyte-like phenotype and possible endothelialization was found in locations close to vasculature channels, indicating angiogenesis potential. Both biaxial and uniaxial mechanical testing showed a stiffer mechanical response of the acellular myocardial scaffolds; however, tissue extensibility and tensile modulus were found to recover in the constructs along with the culture time, as expected from increased cellular content. The cardiac patch that we envision for clinical application will benefit from the natural architecture of myocardial extracellular matrix, which has the potential to promote stem cell differentiation, cardiac regeneration, and angiogenesis.

Chitosan, a derivative of the bio-polysaccharide chitin, has shown promise as a bioactive material for implant, tissue engineering and drug-delivery applications. The aim of this study was to evaluate the contact angle, protein adsorption and osteoblast precursor cell attachment to chitosan coatings bonded to titanium. Rough ground titanium (Ti) coupons were solution cast and bonded to 91.2% de-acetylated chitosan (1 wt% chitosan in 0.2% acetic acid) coatings via silane reactions. Non-coated Ti was used as controls. Samples were sterilized by ethylene oxide gas prior to experiments. Contact angles on all surfaces were measured using water. 5 x 10(4) cells/ml of ATCC CRL 1486 human embryonic palatal mesenchyme (HEPM) cells, an osteoblast precursor cell line, were used for the cell attachment study. SEM evaluations were performed on cells attached to all surfaces. Contact angles and cell attachment on all surfaces were statistically analyzed using ANOVA. The chitosan-coated surfaces (76.4 +/- 5.1 degrees) exhibited a significantly greater contact angle compared to control Ti surfaces (32.2 +/- 6.1 degrees). Similarly, chitosan-coated surfaces exhibited significantly greater (P < 0.001) albumin adsorption, fibronectin adsorption and cell attachment, as compared to the control Ti surfaces. Coating chitosan on Ti surfaces decreased the wettability of the Ti, but increased protein adsorption and cell attachment. Increased protein absorption and cell attachment on the chitosan-coated Ti may be of benefit in enhancing osseointegration of implant devices.

These data support the hypothesis that chitosan-coatings are able to develop a close bony apposition or the osseointegration of dental/craniofacial and orthopedic implants.

FW, FT, and OF may perform better in reconstructive procedures, where increased strength and stiffness are considered to be beneficial.

As part of a program of research aimed at determining the role of mechanical forces in connective tissue differentiation, we have developed a model for investigating the effects of dynamic compressive loading on chondrocyte differentiation in vitro. In the current study, we examined the influence of cyclic compressive loading of chick limb bud mesenchymal cells to a constant peak stress of 9.25 kPa during each of the first 3 days in culture. Cells embedded in agarose gel were subjected to uniaxial, cyclic compression at 0.03, 0.15, or 0.33 Hz for 2 h. In addition, load durations of 12, 54, or 120 min were evaluated while holding frequency constant at 0.33 Hz. For a 2 h duration, there was no response to loading at 0.03 Hz. A significant increase in chondrocyte differentiation was associated with loading at 0.15 Hz, and an even greater increase with loading at 0.33 Hz. Holding frequency constant at 0.33 Hz, a loading duration of 12 min elicited no response, whereas chondrocyte differentiation was enhanced by loading for either 54 or 120 min. Although not statistically significant from the 120 min response, average cartilage nodule density and glycosaminoglycan synthesis rate were highest in the 54 min duration group. This result suggests that cells may be sensitive to the level of cumulative ͑nonrecoverable͒ compressive strain, as well as to the dynamic strain history.

It is well established that mechanical loading is important to homeostasis of cartilage tissue, and growing evidence suggests that it influences cartilage differentiation as well. Whereas the effect of mechanical forces on chondrocyte biosynthesis and gene expression has been vigorously investigated, the effect of the mechanical environment on chondrocyte differentiation has received little attention. The long-term objective of this research is to investigate the regulatory role of mechanical loading in cell differentiation. The goal of this study was to determine if mechanical compression could modulate chondrocyte differentiation in vitro. Stage 23/24 chick limb-bud cells, embedded in agarose gel, were subjected to either static (constant 4.5-kPa stress) or cyclic (9.0-kPa peak stress at 0.33 Hz) loading in unconfined compression during the initial phase of commitment to a phenotypic lineage. Compared with nonloaded controls, cyclic compressive loading roughly doubled the number of cartilage nodules and the amount of sulfate incorporation on day 8, whereas static compression had little effect on these two measures. Neither compression protocol significantly affected overall cell viability or the proliferation of cells within nodules. Since limb-bud mesenchymal cells were seeded directly into agarose, an assessment of cartilage nodules in the agarose reflects the proportion of the original cells that had given rise to chondrocytes. Thus, the results indicate that about twice as many mesenchymal cells were induced to enter the chondrogenic pathway by cyclic mechanical compression. The coincidence of the increase in sulfate incorporation and nodule density indicates that the primary effect of mechanical compression on mesenchymal cells was on cellular differentiation and not on their subsequent metabolism. Further studies are needed to identify the primary chondrogenic signal associated with cyclic compressive loading and to determine the mechanism by which it influences commitment to or progression through the chondrogenic lineage, or both.