Contact-line pinning is a fundamental limitation to the motion of contact lines of liquids on solid surfaces. When a sessile droplet evaporates, contact-line pinning typically results in either a stick–slip evaporation mode, where the contact line pins and depins from the surface in an uncontrolled manner, or a constant contact-area mode with a pinned contact line. Pinning prevents the observation of the quasi-equilibrium constant contact-angle mode of evaporation, which has never been observed for sessile droplets of water directly resting on a smooth, nontextured, solid surface. Here, we report the evaporation of a sessile droplet from a flat glass substrate treated with a smooth, slippery, omni-phobic covalently attached liquid-like coating. Our characterization of the surfaces shows high contact line mobility with an extremely low contact-angle hysteresis of ∼1° and reveals a step change in the value of the contact angle from 101° to 105° between a relative humidity (RH) of 30 and 40%, in a manner reminiscent of the transition observed in a type V adsorption isotherm. We observe the evaporation of small sessile droplets in a chamber held at a constant temperature, T = (25.0 ± 0.1) °C and at constant RH across the range RH = 10–70%. In all cases, a constant contact-angle mode of evaporation is observed for most of the evaporation time. Furthermore, we analyze the evaporation sequences using the Picknett and Bexon ideal constant contact-angle mode for diffusion-limited evaporation. The resulting estimate for the diffusion coefficient, D E, of water vapor in air of D E = (2.44 ± 0.48) × 10–5 m2 s–1 is accurate to within 2% of the value reported in the literature, thus validating the constant contact-angle mode of the diffusion-limited evaporation model.

Conventional grading of dental students' projects in preclinical courses has mainly relied on visual evaluation by experienced instructors. The purpose of this study was to compare conventional visual grading in a dental anatomy course at one U.S. dental school to a novel digital assessment technique. A total of sixty samples comprised of two sets of faculty wax-ups (n=30), student wax-ups (n=15), and dentoform teeth of tooth #14 (n=15) were used for this study. Two additional faculty members visually graded the samples according to a checklist and then repeated the grading after one week. The sample wax-up with the highest score based on the visual grading was selected as the master model for the digital grading, which was also performed twice with an interim period of one week. Descriptive statistics and signed rank tests for systematic bias were used for intra-and interrater comparisons. The intraclass correlation (ICC) was used as a measure of intra-and interrater reliability. None of the faculty members achieved the minimum acceptable intrarater agreement of 0.8. Interrater agreement was substantially less than intrarater agreement for the visual grading, whereas all measures of intrarater agreement were greater than 0.9 and considered excellent for the digital assessment technique. These results suggest that visual grading is limited by modest intrarater reliability and low interrater agreement. Digital grading is a promising evaluation method showing excellent intrarater reliability and correlation. Correlation for visual and digital grading was consistently modest, partly supporting the potential use of digital technology in dental anatomy grading.

Contact-line pinning and dynamic friction are fundamental forces that oppose the motion of droplets on solid surfaces. Everyday experience suggests that if a solid surface offers low contact-line pinning, it will also impart a relatively low dynamic friction to a moving droplet. Examples of such surfaces are superhydrophobic, slippery porous liquid-infused, and lubricant-impregnated surfaces. Here, however, we show that slippery omniphobic covalently attached liquid-like (SOCAL) surfaces have a remarkable combination of contact-angle hysteresis and contact-line friction properties, which lead to very low droplet pinning but high dynamic friction against the motion of droplets. We present experiments of the response of water droplets to changes in volume at controlled temperature and humidity conditions, which we separately compare to the predictions of a hydrodynamic model and a contact-line model based on molecular kinetic theory. Our results show that SOCAL surfaces offer very low contact-angle hysteresis, between 1 and 3°, but an unexpectedly high dynamic friction controlled by the contact line, where the typical relaxation time scale is on the order of seconds, 4 orders of magnitude larger than the prediction of the classical hydrodynamic model. Our results highlight the remarkable wettability of SOCAL surfaces and their potential application as low-pinning, slow droplet shedding surfaces.

Biofilms are central to some of the most urgent global challenges across diverse fields of application, from medicine to industries to the environment, and exert considerable economic and social impact. A fundamental assumption in anti-biofilms has been that the coating on a substrate surface is solid. The invention of slippery liquid-infused porous surfaces—a continuously wet lubricating coating retained on a solid surface by capillary forces—has led to this being challenged. However, in situations where flow occurs, shear stress may deplete the lubricant and affect the anti-biofilm performance. Here, we report on the use of slippery omniphobic covalently attached liquid (SOCAL) surfaces, which provide a surface coating with short (ca. 4 nm) non-cross-linked polydimethylsiloxane (PDMS) chains retaining liquid–surface properties, as an antibiofilm strategy stable under shear stress from flow. This surface reduced biofilm formation of the key biofilm-forming pathogens Staphylococcus epidermidis and Pseudomonas aeruginosa by three–four orders of magnitude compared to the widely used medical implant material PDMS after 7 days under static and dynamic culture conditions. Throughout the entire dynamic culture period of P. aeruginosa , SOCAL significantly outperformed a typical antibiofilm slippery surface [i.e., swollen PDMS in silicone oil (S-PDMS)]. We have revealed that significant oil loss occurred after 2–7 day flow for S-PDMS, which correlated to increased contact angle hysteresis (CAH), indicating a degradation of the slippery surface properties, and biofilm formation, while SOCAL has stable CAH and sustainable antibiofilm performance after 7 day flow. The significance of this correlation is to provide a useful easy-to-measure physical parameter as an indicator for long-term antibiofilm performance. This biofilm-resistant liquid-like solid surface offers a new antibiofilm strategy for applications in medical devices and other areas where biofilm development is problematic.

Sessile droplet evaporation underpins a wide range of applications from inkjet printing to coating. However, drying times can be variable and contact-line pinning often leads to undesirable effects, such as ring stain formation. Here, we show voltage programmable control of contact angles during evaporation on two pinning-free surfaces. We use an electrowetting-on-dielectric approach and Slippery Liquid-Infused Porous (SLIP) and Slippery Omniphobic Covalently Attached Liquid-Like (SOCAL) surfaces to achieve a constant contact angle mode of evaporation. We report evaporation sequences and droplet lifetimes across a broad range of contact angles from 105°−67°. The values of the contact angles during evaporation are consistent with expectations from electrowetting and the Young-Lippman equation. The droplet contact areas reduce linearly in time, and this provides estimates of diffusion coefficients close to the expected literature value. We further find that the total time of evaporation over the broad contact angle range studied is only weakly dependent on the value of the contact angle. We conclude that on these types of slippery surfaces, droplet lifetimes can be predicted and controlled by the droplet's volume and physical properties (density, diffusion coefficient, and vapor concentration difference to the vapor phase) largely independent of the precise value of contact angle. These results are relevant to applications, such as printing, spraying, coating, and other processes, where controlling droplet evaporation and drying is important.

Slippery liquid-infused porous surfaces (SLIPS) are an innovation that reduces droplet-solid contact line pinning and interfacial friction. Recently, it has been shown that a liquid analogue of Young’s law can be deduced for the apparent contact angle of a sessile droplet on SLIPS despite there never being contact by the droplet with the underlying solid. Since contact angles on solids are used to characterize solid–liquid interfacial interactions and the wetting of a solid by a liquid, it is our hypothesis that liquid–liquid interactions and the wetting of a liquid surface by a liquid can be characterized by apparent contact angles on SLIPS. Here, we first present a theory for deducing liquid–liquid interfacial tensions from apparent contact angles. This theory is valid irrespective of whether or not a film of the infusing liquid cloaks the droplet–vapor interface. We show experimentally that liquid–liquid interfacial tensions deduced from apparent contact angles of droplets on SLIPS are in excellent agreement with values from the traditional pendant drop technique. We then consider whether the Zisman method for characterizing the wettability of a solid surface can be applied to liquid surfaces created using SLIPS. We report apparent contact angles for a homologous series of alkanes on Krytox-infused SLIPS and for water–IPA mixtures on both the Krytox-infused SLIPS and a silicone oil-infused SLIPS. The alkanes on the Krytox-infused SLIPS follow a linear relationship in the liquid form of the Zisman plot provided that the effective droplet–vapor interfacial tension is used. All three systems follow a linear relationship on a modified Zisman plot. We interpret these results using the concept of the critical surface tension (CST) for the wettability of a solid surface introduced by Zisman. In our liquid surface case, the obtained critical surface tensions were found to be lower than the infusing liquid–vapor surface tensions.

Liquid-infused surfaces (LISs) exhibit unique properties that make them ideal candidates for a wide range of applications, from antifouling and anti-icing coatings to self-healing surfaces and controlled wetting. However, when exposed to realistic environmental conditions, LISs tend to age and progressively lose their desirable properties, potentially compromising their application. The associated ageing mechanisms are still poorly understood, and results reflecting real-life applications are scarce. Here, we track the ageing of a model LIS composed of glass surfaces functionalized with hydrophobic nanoparticles and infused with silicone oil. The LISs are fully submerged in aqueous solutions and exposed to acoustic pressure waves for set time intervals. The ageing is monitored by periodic measurements of the LIS's wetting properties. We also track the changes to the LIS's nanoscale structure. We find that the LISs rapidly lose their slippery properties because of a combination of oil loss, smoothing of the nanoporous functional layer, and substrate degradation when directly exposed to the solution. The oil loss is consistent with water microdroplets entering the oil layer and displacing oil away from the surface. These mechanisms are general and could play a role in the ageing of most LISs.

No abstract