This article presents the development of an underwater gripper that utilizes soft robotics technology to delicately manipulate and sample fragile species on the deep reef. Existing solutions for deep sea robotic manipulation have historically been driven by the oil industry, resulting in destructive interactions with undersea life. Soft material robotics relies on compliant materials that are inherently impedance matched to natural environments and to soft or fragile organisms. We demonstrate design principles for soft robot end effectors, bench-top characterization of their grasping performance, and conclude by describing in situ testing at mesophotic depths. The result is the first use of soft robotics in the deep sea for the nondestructive sampling of benthic fauna.

In this paper, a new concept of formation learning control is introduced to the field of formation control of multiple autonomous underwater vehicles (AUVs), which specifies a joint objective of distributed formation tracking control and learning/identification of nonlinear uncertain AUV dynamics. A novel two-layer distributed formation learning control scheme is proposed, which consists of an upper-layer distributed adaptive observer and a lower-layer decentralized deterministic learning controller. This new formation learning control scheme advances existing techniques in three important ways: 1) the multi-AUV system under consideration has heterogeneous nonlinear uncertain dynamics; 2) the formation learning control protocol can be designed and implemented by each local AUV agent in a fully distributed fashion without using any global information; and 3) in addition to the formation control performance, the distributed control protocol is also capable of accurately identifying the AUVs' heterogeneous nonlinear uncertain dynamics and utilizing experiences to improve formation control performance. Extensive simulations have been conducted to demonstrate the effectiveness of the proposed results.

No abstract

Abstract-In this work we experimentally demonstrate (a) that the holding strength of universal jamming grippers increases as a function of the jamming pressure to greater than three atmospheres, and (b) that jamming grippers can be used for deep sea grasping tasks in ambient pressures exceeding one hundred atmospheres, where such high jamming pressures can be readily achieved. Laboratory experiments in a pressurized, water filled test cell are used to measure the holding force of a 'universal' style jamming gripper as a function of the pressure difference between internal membrane pressure and ambient pressure. Experiments at sea are used to demonstrate that jamming grippers can be installed on, and operated from, remotely operated vehicles (ROVs) at depths in excess of 1200m. In both experiments, the jamming gripper consists of a latex balloon filled with a mixture of fresh water and ~200 micron glass beads, which are cheaply available in large quantities as sand blasting media. The use of a liquid, rather than gas, as the fluid media allows operation of the gripper with a closed loop fluid system; jamming pressure is controlled with an electrically driven water hydraulic cylinder in the lab, and with an oil hydraulic driven large-bore water hydraulic cylinder at sea.

No abstract

SUMMARYWe show experimentally that flapping foil kinematics consisting of a power downstroke and a feathering upstroke together with a properly timed in-line motion, similar to those employed in forelimb propulsion of sea turtles, can produce high thrust and be hydrodynamically as efficient as symmetrically flapping foils. The crucial parameter for such asymmetrically flapping foils is a properly sized and timed in-line motion, whose effect is quantified by a new parameter, the advance angle, defined as the angle of the foil trajectory with respect to the horizontal, evaluated at the middle of the power downstroke. We show, in particular, that optimal efficiency in high aspect ratio rigid foils, accompanied by significant thrust production, is obtained for Strouhal numbers in the range 0.2-0.6 for Reynolds number equal to 13,000, and for values of the advance angle around 0.55 (100deg.). The optimized kinematics consist of the foil moving back axially during the downstroke, in the direction of the oncoming flow, and rotating with a large pitch angle. This causes the force vector to rotate and become nearly parallel to the steady flow, thus providing a large thrust and a smaller transverse force. During the upstroke, the foil is feathering while it moves axially forward, i.e. away from the vorticity shed during the power stroke; as a result, the transverse force remains relatively small and no large drag force is produced. Observations from turtles confirm qualitatively the findings from the foil experiments.

We demonstrate experimentally that flapping foils within an oncoming stream can efficiently extract energy from the flow, thus offering an attractive, alternative way for energy production. The greatest promise for flapping foils is to use them in unsteady and turbulent flow, where their own unsteady motion can be controlled to maximize energy extraction. The foils in this study perform a sinusoidal linear motion (sway, or heave) in combination with a sinusoidal angular motion (yaw or pitch); the effect of three principal parameters is studied systematically, yaw amplitude, the Strouhal number, and the phase angle between sway and yaw. The foils are made of aluminum, in the shape of NACA 0012 airfoils, using three different aspect ratios, 4.1, 5.9, and 7.9; they were tested at Reynolds numbers around 14,000. Efficiencies of up to 52 ± 3% are achieved with simple sinusoidal motions, thus demonstrating that foils can efficiently extract energy from unsteady flows.

No abstract