The usage of data transmission through Optical Fiber is highly preferred in every area where transferring of data is needed from one end to another. Moreover, nowadays the infrastructure of telecommunications is in good shape and size to handle data transmission through its optical fibers which have low attenuation and higher bandwidth. The seeking of data rate higher than 100Gbit/second and above has been increased to build it in urban and rural areas, and for long and short hauls. Consequently, the current goal is to propel this transmission system into the next appropriated level to avoid any decline of the optical infrastructure than its current capacity. To fulfill increased demand for bandwidth in Broadband services one of the most trusted technology is the Orthogonal Frequency Division Multiplexing (OFDM). The Orthogonal Frequency Division Multiplexing has been placed on-demand in optical communication, it is used in Long haul transmission Format in Direct and Coherent detection. OFDM has many features and abilities can boost the optical fiber performance by eliminating several limits of conventional Optical Fiber communication. OFDMA has polarization mode dispersion (PMD) and chromatic dispersion (CD) which are considered a big addition to the current systems. In addition to that, the easy correlation of the coherent optical OFDM with Wavelength Division Multiplexing (WDM) systems can further advantages in the transmission system such as super bandwidth, high spectral efficiency, and extra data rates. Furthermore, the WDM systems can improve data rate and capacity by using multiple wavelengths over a single fiber. This work aims to bring implementation and to perform a deep-dive study of higher data rates using Direct and Coherent Optical OFDM for long path transmissions. This research starts with a unique user and then extends to the add the OFDM - WDM system to get a data rate of 100 Gbps. Regarding the software portion, the Optisystem simulation tool was used for the design and implementation of the system. Moreover, the modulation type used is QAM for the OFDM signal, and I/Q modulation is deployed, while Coherent and Direct detection is used at the receiving portion. Q Factor, the bit error rate and eye diagram were discussed to study the System’s Performance and Quality. This work found CD-OOFDM is the best system for next generation of optical. The work compared WDM CD-OOFDM with SMF-DCF to DD and CD-OOFDM. In addition to that, it compared WDM CD-OOFDM with SMF-DCF to CD-OODFM with SMF. Therefore, the results showed that WDM CD-OOFDM with SMF-DCF achieved 25 Gbps for four channels of the WDM system at 120km channel, where the carrier frequencies were from 193.05THz to 193.2THz.

In this work, a pollution-sensitive Photonic Crystal Fiber (PCF) based on Surface Plasmon Resonance (SPR) technology is designed and implemented for sensing refractive indices and concentrations of polluted  water . The overall construction of the sensor is achieved by splicing short lengths of PCF (ESM-12) solid core on one side with traditional multimode fiber (MMF) and depositing a gold nanofilm of 50nm thickness on the end of the PCF sensor. The PCF- SPR experiment was carried out with various samples of polluted water including(distilled water, draining water, dirty pond water, chemical water, salty  water and oiled water). The location of the resonant wavelength peaks is seen to move to longer wavelengths (red shift) as the refractive index increases due to the transfer of maximum energy from the reflected power of the light guided through the fiber to the surface plasmons. The experimental results show that the highest sensitivity reached 4202.6nm/RIU for oiled water, the signal to noise ratio was 0.625, the resolution was 2.4*10-5 RIU, and the figure of merit was 22.8. The prepared sensor exhibited excellent performance features, making it an excellent element for detecting water pollutants.

Photonic Crystal Fiber (PCF) based on the Surface Plasmon Resonance (SPR) effect has been proposed to detect polluted water samples. The sensing characteristics are illustrated using the finite element method. The right hole of the right side of PCF core has been coated with chemically stable gold material to achieve the practical sensing approach. The performance parameter of the proposed sensor is investigated in terms of wavelength sensitivity, amplitude sensitivity, sensor resolution, and linearity of the resonant wavelength with the variation of refractive index of analyte. In the sensing range of 1.33 to 1.3624, maximum sensitivities of 1360.2 nm ∕ RIU and 184 RIU −1 are achieved with the high sensor resolutions of 7 ×10 -5 RIU and 5.4× 10 −5 RIU using wavelength and amplitude interrogation methods, respectively. The proposed sensor could be established to detect various refractive index (RI) of pollutions in water.

Surface Plasmon Resonance (SPR) - based plastic optical fiber has been provided as a sensor to estimating the refractive index and then the concentration of specific chemical samples. Two configurations were suggested for a design. The first was through using a single layer of gold with a thickness of about 40nm deposited on a 10mm portion in the middle of plastic optical fiber. In the second configuration, a bilayer deposited on the fiber. This bilayer consisted of a gold layer with a thickness of about 30 nm and an aluminum layer with a thickness of about 30 nm. Both of these configurations utilized as a chemical sensor. The resonance wavelength for the bilayer-based sensor was higher than that of the single-layer sensor for all studied chemical samples. The highest resonance wavelength was for the salt-water solution with a concentration of 30%. For the salt-water solution with a concentration of 30%, the resonance wavelength with the bilayer-based sensor was 568nm while it was 540nm with the single-layer sensor.

In this work, a Photonic Crystal Fiber (PCF) sensor based on the Surface Plasmon Resonance (SPR) technology was proposed. A thin layer of gold (Au) was deposited on a D-shaped Photonic Crystal Fiber (PCF), which was coated with plasmonic chemically stable gold material with a thickness of 40nm. The performance parameters like sensitivity including wavelength sensitivity and amplitude sensitivity and resolution were evaluated by simulation using COMSOL software. The proposed sensor was created by using the finite element approach, it is numerically examined. The results show that the surface of D-shaped Photonic Crystal Fiber coated with Au behaves as a sensor to detect the refractive index (IR) of toxic metal ions. The impacts of the structural characteristics on the resonant spectra are also researched in order to improve sensing performance. The greatest amplitude sensitivity  was 99.2 RIU-1 and maximum resolution was 4 x 10-5 RIU achieved within the detection range (1.351-1.363).