No abstract

No abstract

The startup process occurs frequently for pumped storage units. During this process, the rotating rate that changes rapidly and unsteady flow in runner cause the complex dynamic response of runner, sometimes even resonance. The sharp rise of stress and the large-amplitude dynamic stresses of runner will greatly shorten the fatigue life. Thus, the study of start-up process in turbine mode is critical to the safety operation. This paper introduced a method of coupling one dimensional (1D) pipeline calculation and three-dimensional computational dynamics (3D CFD) simulation to analyze transient unsteady flow in units and to obtain more accurate and reliable dynamic stresses results during start up process. According to the results, stress of the ring near fixed support increased quickly as rotating rate rose and became larger than at fillets of leading edge and band in the later stages of start-up. In addition, it was found that dynamic response can be caused by rotor stator interaction (RSI), but also could even be generated by the severe pressure fluctuation in clearance, which can also be a leading factor of dynamic stresses. This study will facilitate further estimation of dynamic stresses in complex flow and changing rotating rate cases, as well as fatigue analysis of runner during transient operation.

No abstract

Purpose The gaps between runner and nearby structures play an important role in the dynamic response of runner, especially for pump-turbines. This paper aims to evaluate the gap influence on the added mass and dynamic stress of pump-turbine runner and provide an improved method to predict the resonance of runner. Design/methodology/approach Acoustic-structural coupling method was used to evaluate the added mass factors of a reduced scale pump-turbine with different axial and radial gap size between runner and nearby rigid walls. Improved one-way fluid-structural interaction (FSI) simulation was used to calculate the dynamic stress of the runner, which takes into account fluid added mass effect. The time-dependent hydraulic forces on the runner surfaces that were obtained from unsteady CFD simulation were transferred to the runner structure as a boundary condition, by using mesh-matching algorithm at the FSI surfaces. Findings The results show that the added mass factors increase as the gap size decreases. The axial gaps have greater influence on the added mass factors for the in-phase (IP) modes than the counter-phase (CP) and crown-dominant (CD) modes, while the CP and CD modes are very sensitive to the radial gaps. The largest added mass factor is observed in (2 + 4)ND-CP mode (resonance mode). The results reveal that the transient structural dynamic stress analysis, with the consideration of gaps and fluid added mass, can accurately predict the resonance phenomenon. Resonance curve of the pump-turbine has been obtained which agrees well with the test result. The gap fluid has great influence on the resonance condition, while for non-resonance operating points, the effect of gaps on the dynamic stress amplitude is quite small. Originality/value This paper provides an accurate method to analyze the dynamic response during runner design stage for safety assessment. The resonance curve prediction has more significance than previous methods which predict the resonance of runner by modal or harmonic analysis.

No abstract

No abstract

After long-term operation, the material loss due to slurry erosion often leads to significant changes in the impeller geometry. This change can, in turn, affect the flow characteristics and the erosion mechanism in a centrifugal pump. To investigate this matter, we consider two geometric models based on a prototype stainless steel impeller, which failed due to huge erosion problems from the pulp slurry. These two models are different in the degree of wear, with one model at the pre-erosion stage and the other with worn blades. For both models, the flow characteristics have been obtained in the Eulerian reference frame by means of the SST k-ω model. Then, in order to determine the erosion patterns, the particles have been tracked in the Lagrangian reference frame. In this way, the influence of the flow characteristics on the erosion patterns has been analyzed. Results show that the geometric variations greatly affect the flow characteristics, and consequently the erosion patterns. Particularly, it has been found that the clearance flow plays a significant role in defining erosion characteristics, such as erosion distribution, areas, and rates. Interestingly, the simulation results for current study show that the erosion rates after long-term operation greatly decrease near both the outlet edge and the blade bottom. It follows also that for accurate erosion predictions, these geometric variations have to be considered in the numerical model. This paper provides a better understanding of the complex erosion mechanism in centrifugal pumps, which can help to reduce the wear in future designs.