The paper reports on the properties of UV-curable inorganic-organic hybrid polymer multimode optical channel waveguides fabricated by roll-to-plate (R2P) nanoimprinting. We measured transmission spectra, refractive indices of the applied polymer materials, and optimized the R2P fabrication process. Optical losses of the waveguides were measured by the cut-back method at wavelengths of 532, 650, 850, 1310, and 1550 nm. The lowest optical losses were measured at 850 nm and the lowest average value was 0.19 dB/cm, and optical losses at 1310 nm were 0.42 dB/cm and 0.25 dB/cm at 650 nm respectively. The study has demonstrated that nanoimprinting has great potential for the implementation of optical polymer waveguides not only for optical interconnection applications.

The nanoimprint replication of biomimetic nanostructures can be interesting for a wide range of applications. We demonstrate the process chain for Morpho-blue-inspired nanostructures, which are especially challenging for the nanoimprint process, since they consist of multilayer undercut structures, which typically cannot be replicated using nanoimprint lithography. To achieve this, we used a specially made, proprietary imprint material to firstly allow successful stamp fabrication from an undercut master structure, and secondly to enable UV-based nanoimprinting using the same material. Nanoimprinting was performed on polymer substrates with stamps on polymer backplanes to be compatible with roller-based imprinting processes. We started with single layer undercut structures to finally show that it is possible to successfully replicate a multilayer undercut stamp from a multilayer undercut master and use this stamp to obtain multilayer undercut nanoimprinted samples.

In this work, we present a fabrication procedure of metal nanomesh arrays with the newly developed nanoimprint resist mr-NIL212FC used in a bi-layer resist system for a lift-off process. We comparatively analyzed and evaluated nanomeshes fabricated with a freshly prepared h-PDMS/PDMS stamp and a stamp used 501 times. Therefore, we first performed a step&repeat imprint test run in a self-built low cost step&repeat UV-NIL setup. We inspected the imprint behavior of the stamp, the UV-transmission through the stamp as well as stamp lifetime and stamp degradation with regard to the possible changes of its surface roughness. The nanomesh fabrication process is characterized by a good lift-off performance, leading to a low defect density of <1.26 defects 100 µm−2. Even after 501 imprints, only a negligible stamp degradation occurred without effecting the imprint performance. Likewise, the same holds true for the nanomeshes, which showed comparable low defect densities and feature sheet resistances of 3.54 ± 0.14 Ω/□ for the first and 3.48 ± 0.23 Ω/□ for the 501st nanomesh, respectively. AFM analyses further revealed that the maximum height of the roughness Rt changed over the course of the 501 imprints from 6.3 nm to 13.3 nm, representing <5% of the overall imprint height. In general, the mr-NIL212FC resist shows a good wettability and compatibility with standard h-PDMS/PDMS stamps, a fast curing behavior, a high replication fidelity, easy separation characteristics, and a very low diffusion of resist components into the stamp. The mr-NIL212FC resist allows exposure times as short as 2 s in the applied tool setup, enabling high throughput production. Moreover, all performed measurements indicate that a much higher number of imprints with one stamp seem possible.

Structural anti-reflective coating and bactericidal surfaces, as well as many other effects, rely on high-aspect-ratio (HAR) micro- and nanostructures, and thus, are of great interest for a wide range of applications. To date, there is no widespread fabrication of dense or isolated HAR nanopillars based on UV nanoimprint lithography (UV-NIL). In addition, little research on fabricating isolated HAR nanopillars via UV-NIL exists. In this work, we investigated the mastering and replication of HAR nanopillars with the smallest possible diameters for dense and isolated arrangements. For this purpose, a UV-based nanoimprint lithography process was developed. Stability investigations with capillary forces were performed and compared with simulations. Finally, strategies were developed in order to increase the stability of imprinted nanopillars or to convert them into nanoelectrodes. We present UV-NIL replication of pillars with aspect ratios reaching up to 15 with tip diameters down to 35 nm for the first time. We show that the stability could be increased by a factor of 58 when coating them with a 20 nm gold layer and by a factor of 164 when adding an additional 20 nm thick layer of SiN. The coating of the imprints significantly improved the stability of the nanopillars, thus making them interesting for a wide range of applications.

No abstract