Heat stress is one of the most stressful events in livestock life, negatively impacting animal health, productivity, and product quality. Moreover, the negative impact of heat stress on animal product quality has recently attracted increasing public awareness and concern. The purpose of this review is to discuss the effects of heat stress on the quality and the physicochemical component of meat in ruminants, pigs, rabbits, and poultry. Based on PRISMA guidelines, research articles were identified, screened, and summarized based on inclusion criteria for heat stress on meat safety and quality. Data were obtained from the Web of Science. Many studies reported the increased incidences of heat stress on animal welfare and meat quality. Although heat stress impacts can be variable depending on the severity and duration, the exposure of animals to heat stress (HS) can affect meat quality. Recent studies have shown that HS not only causes physiological and metabolic disturbances in living animals but also alters the rate and extent of glycolysis in postmortem muscles, resulting in changes in pH values that affect carcasses and meat. It has been shown to have a plausible effect on quality and antioxidant activity. Acute heat stress just before slaughter stimulates muscle glycogenolysis and can result in pale, tender, and exudative (PSE) meat characterized by low water-holding capacity (WHC). The enzymatic antioxidants such as superoxide dismutase (SOD), catalase (CAT), and glutathione peroxidase (GPx) act by scavenging both intracellular and extracellular superoxide radicals and preventing the lipid peroxidation of the plasma membrane. Therefore, understanding and controlling environmental conditions is crucial to successful animal production and product safety. The objective of this review was to investigate the effects of HS on meat quality and antioxidant status.

An experimental design was applied for the optimization of the extraction process of two preservatives, benzoic and sorbic acids (BA, SA), from food drinks. A simple, rapid, and reliable solid-phase extraction (SPE) method for the simultaneous extraction of these two preservatives and their determination by liquid chromatography with a diode array detector was considered. Box–Behnken design (BBD) was applied to both steps of the SPE process: (i) the sample percolation to ensure the retention of the totality of the acids by the silica-based C18 sorbent; (ii) the elution step to ensure desorption of the totality of the acids from the cartridge. Thus, the volume, pH, and flow rate of the sample, and the percentage of MeOH, volume, and flow rate of the elution solvent, were optimized. Sample volume and pH have a significant influence (p < 0.0001 and p = 0.0115) on the percolation yield. However, no effect was recorded for the flow rate (p > 0.05). Flow rate also has no significant effect on the elution efficiency. The proposed new solid-phase extraction method, which can be easily applied to routine monitoring of preservatives BA and SA in juice and soft drink samples, included 0.5 g of C18 sorbent, 1 mL of food drink adjusted to pH 1 and percolated at 4.5 mL min−1, and 1 mL of a solvent mixture composed of methanol/acidified water (pH = 2.6) (90:10, v/v) used in the elution step at a flow rate of 4.5 mL min−1. Validation of the SPE method and the technique of analysis were evaluated, namely, the accuracy, precision, detection, and quantification limits and linearity. Recovery percentages of benzoic and sorbic acids were above 95% with relative standard deviations lower than 1.78%. Detection and quantification limits were 0.177 and 0.592 µg mL−1, and 0.502 and 0.873 µg mL−1 for benzoic acid and sorbic acid respectively. Optimal conditions were applied to commercial fruit juices and soft drinks and a minimal matrix effect was observed. This method was compared with other SPE methods using oxidized activated carbon and multiwalled carbon nanotubes as adsorbents. The yields determined with these last two were low compared to those determined with our method.

In this work, a rapid, precise, and cost-valuable method has been established to quantify phenolic compounds in olive oil using new-based hydrophilic interaction solid-phase extraction (SPE). Boehlert’s experimental design applied the determination of the optimal operating conditions. An investigation into the effects of the methanol composition (50–100%), the volume of eluent (1–12 mL), and pH (1–3) on the extraction of phenols acids and total phenols from Tunisian olive oils was performed. The results showed that the extraction conditions had a significant effect on the extraction efficiency. The experiment showed that the greatest conditions for the SPE of phenolic acids were the methanol composition at 90.3%, pH at 2.9, and volume at 7.5 mL, respectively. The optimal conditions were applied to different types of olive oils, and it could be concluded that larger concentrations of polyphenols were found in extra virgin olive oil (89.15–218), whereas the lowest levels of these compounds (66.8 and 5.1) were found in cold-pressed crude olive oil and olive pomace oil, respectively.