The effective stress law for the permeability of a limestone is studied experimentally by performing constant head permeability tests in a triaxial cell with different conditions of confining pressure and pore pressure. Test results have shown that a pore pressure increase and a confining pressure decrease both result in an increase of the permeability, and that the effect of the pore pressure change on the variation of the permeability is more important than the effect of a change of the confining pressure. A power law is proposed for the variation of the permeability with the effective stress. The permeability effective stress coefficient increases linearly with the differential pressure and is greater than one as soon the differential pressure exceeds few bars. The test results are well reproduced using the proposed permeability-effective stress law. A conceptual pore-shell model based on a detailed observation of the microstructure of the studied limestone is proposed. This model is able to explain the experimental observations on the effect of the total stress and of the pore pressure on the permeability of the limestone. Effective stress coefficients for the stress-dependent permeability which are greater than one are obtained. It is shown that the controlling factor is the ratio of the different bulk moduli of the various constituents of the rock. This ratio is studied experimentally by performing microhardness tests.Comment: International Journal of Rock Mechanics and Mining Sciences (2008) In pres

Temperature increase in saturated porous materials under undrained conditions leads to thermal pressurization of the pore fluid due to the discrepancy between the thermal expansion coefficients of the pore fluid and of the solid matrix. This increase in the pore fluid pressure induces a reduction of the effective mean stress and can lead to shear failure or hydraulic fracturing. The equations governing the phenomenon of thermal pressurization are presented and this phenomenon is studied experimentally for a saturated granular rock in an undrained heating test under constant isotropic stress. Careful analysis of the effect of mechanical and thermal deformation of the drainage and pressure measurement system is performed and a correction of the measured pore pressure is introduced. The test results are modelled using a non-linear thermo-poro-elastic constitutive model of the granular rock with emphasis on the stress-dependent character of the rock compressibility. The effects of stress and temperature on thermal pressurization observed in the tests are correctly reproduced by the model

International audienceThe poromechanical behaviour of hardened cement paste under isotropic loading is studied on the basis of an experimental testing program of drained, undrained and unjacketed compression tests. The macroscopic behaviour of the material is described in the framework of the mechanics of porous media. The poroelastic parameters of the material are determined and the effect of stress and pore pressure on them is evaluated. Appropriate effective stress laws which control the evolution of total volume, pore volume, solid volume, porosity and drained bulk modulus are discussed. A phenomenon of degradation of elastic properties is observed in the test results. The microscopic observations showed that this degradation is caused by the microcracking of the material under isotropic loading. The good compatibility and the consistency of the obtained poromechanical parameters demonstrate that the behaviour of the hardened cement paste can be indeed described within the framework of the theory of porous media

A method is presented for the evaluation of the permeability-porosity relationship in a lowpermeability porous material using the results of a single transient test. This method accounts for both elastic and non-elastic deformations of the sample during the test and is applied to a hardened class G oil well cement paste. An initial hydrostatic undrained loading is applied to the sample. The generated excess pore pressure is then released at one end of the sample while monitoring the pore pressure at the other end and the radial strain in the middle of the sample during the dissipation of the pore pressure. These measurements are back analysed to evaluate the permeability and its evolution with porosity change. The effect of creep of the sample during the test on the measured pore pressure and volume change is taken into account in the analysis. This approach permits to calibrate a power law permeability-porosity relationship for the tested hardened cement paste. The porosity sensitivity exponent of the power-law is evaluated equal to 11 and is shown to be mostly independent of the stress level and of the creep strains.

International audienceThe results of a macro-scale experimental study performed on a hardened class G cement paste [Ghabezloo et al. (2008) Cem. Con. Res. (38) 1424-1437] are used in association with the micromechanics modelling and homogenization technique for evaluation of the complete set of poroelastic parameters of the material. The experimental study consisted in drained, undrained and unjacketed isotropic compression tests. Analysis of the experimental results revealed that the active porosity of the studied cement paste is smaller than its total porosity. A multi-scale homogenization model, calibrated on the experimental results, is used to extrapolate the poroelastic parameters to cement pastes prepared with different water-to-cement ratio. The notion of cement paste active porosity is discussed and the poroelastic parameters of hardened cement paste for an ideal, perfectly drained condition are evaluated using the homogenization model

No abstract

Ghabezloo et al. (2008): The effect of undrained heating on a fluid-saturated hardened cement paste 150The effect of undrained heating on a fluid-saturated hardened cement paste AbstractThe effect of undrained heating on volume change and induced pore pressure increase is an important point to properly understand the behaviour and evaluate the integrity of an oil well cement sheath submitted to rapid temperature changes. This thermal pressurization of the pore fluid is due to the discrepancy between the thermal expansion coefficients of the pore fluid and of the solid matrix. The equations governing the undrained thermo-hydro-mechanical response of a porous material are presented and the effect of undrained heating is studied experimentally for a saturated hardened cement paste. The measured value of the thermal pressurization coefficient is equal to 0.6MPa/°C. The drained and undrained thermal expansion coefficients of the hardened cement paste are also measured in the heating tests.The anomalous thermal behaviour of cement paste pore fluid is back analysed from the results of the undrained heating test.

International audienceThe equations governing plane steady-state flow in heterogeneous porous body containing cracks are presented first. Then, a general transformation lemma is presented which allows extending a particular solution obtained for a given flow problem to another configuration with different geometry, behaviour and boundary conditions. An existing potential solution in terms of discharges along the cracks, established by Liolios and Exadaktylos (J Solids Struct 43:3960-3982, 2006) for non-intersecting cracks in isotropic matrix, is extended to intersecting cracks in anisotropic matrix. The basic problem of a single straight crack in an infinite body submitted to a pressure gradient at infinity is then investigated and a closed-form solution is presented for the case of void cracks (infinite conductivity), as well as a semi-analytical solution for the case of cracks with Poiseuille type conductivity. These solutions, derived first for an isotropic matrix, are then extended to anisotropic matrices using the general transformation lemma. Finally, using the solution obtained for a single crack, a closed-form estimation of the effective permeability of micro-cracked porous materials with weak crack density is derived from a self-consistent upscaling scheme