The finite element method is widely used in dental research. The decision to use two-dimensional (2D) or three-dimensional (3D) modelling is dependent on many interrelated factors. The purpose of the present study was to compare and contrast 2D and 3D finite element analysis (FEA) in investigating the mechanical behaviour of a maxillary premolar restored with a full crown under similar conditions of axial and lateral occlusal loading. The 2D analysis required modelling both a buccolingual and mesiodistal section of the restored premolar and for comparison sections of a 3D model were examined. Differences in the results for displacement and maximum principal stress distribution within the component structures and interfaces of the 2D and 3D models were, in general, attributable to differences in geometry represented in the models. Maximum principal stresses tended to be greater under lateral rather than axial occlusal loading. It was concluded that 2D FEA may find application in investigating key aspects of the mechanical behaviour of a dental restoration in a single tooth unit, but that in certain situations combinations of 2D and 3D FEA may offer the best understanding of the biomechanical behaviour of complex dental structures. Sophisticated FE models are required to better understand the mechanical behaviour of restored tooth units.
Second to autologous bone grafts are the calcium phosphate cements (CPCs) used as synthetic bone substitutes due to their chemical similarity to the mineral component of bone. Their ability to conform to complex bone defects and excellent osteoconductivity also render them excellent scaffolds for bone tissue engineering, although they do have their own limitations. Calcium phosphates can be divided into two main categories, namely apatite and brushite. Apatites exhibit low solubility, whereas, calcium phosphates that set to form brushite, are metastable, which degrade rapidly, but do subsequently form hydroxyapatite that retards the rate. In contrast dicalcium phosphate anhydrous (monetite) has a higher solubility than octacalcium phosphate and does not transform to an apatite; thus, it is able to continue to degrade with time. Herein, a new method was used via the addition of sodium chloride to btricalcium phosphate and monocalcium phosphate monohydrate to form micro-and macroporous monetite (DCPA). The X-ray diffraction and FTIR spectra confirmed the formation of monetite in the presence of both, 6.2 M NaCl solution or 60% of solid sodium chloride. The maximum compressive strength (s c ¼ 12.3 AE 1.8 MPa) and the Young's modulus (E ¼ 1.0 AE 0.1 GPa) of the monetite cements obtained were comparable to the upper limits of the values reported for cancellous bone and also higher than that reported by other routes used to form monetite. The porous cements analysed by microCT revealed an interconnected porosity with the preliminary in vitro biological evaluation indicating favourable osteoblast cell attachment and growth.
Non-carious cervical tooth lesions for many decades were attributed to the effects of abrasion and erosion mainly through toothbrush trauma, abrasive toothpaste, and erosive acids. However, though the above may be involved, more recently a biomechanical theory for the formation of these lesions has arisen, and the term abfraction was coined. The aim of this study was to investigate the biomechanics of abfraction lesions in upper canine teeth under axial and lateral loading conditions using a three-dimensional finite element analysis. An extracted human upper canine tooth was scanned by μCT machine (Skyscan, Belgium). These μCT scans were segmented, reconstructed, and meshed using ScanIP (Simpleware, Exeter, UK) to create a three-dimensional finite element model. A 100 N load was applied axially at the incisal edge and laterally at 45° midpalatally to the long axis of the canine tooth. Separately, 200 N axial and non-axial loads were applied simultaneously to the tooth. It was found that stresses were concentrated at the CEJ in all scenarios. Lateral loading produced maximum stresses greater than axial loading, and pulp tissues, however, experienced minimum levels of stresses. This study has contributed towards the understanding of the aetiology of non-carious cervical lesions which is a key in their clinical management.
The purpose of this study was to investigate, by means of the finite element method the mechanical behaviour of three designs of fixed partial denture (FPD) for the replacement of the maxillary first premolar in shortened dental arch therapy. Two-dimensional, linear, static finite element analyses were carried out to investigate the biomechanics of the FPDs and their supporting structures under different scenarios of occlusal loading. Displacement and stress distribution for each design of FPD were examined, with particular attention being paid to the stress variations along the retainer-abutment--and the periodontal ligament-bone interfaces. The results indicated that displacement and maximum principal stresses in the fixed-fixed, three-unit FPD were substantially less than those in the two-unit cantilever FPDs. Of the two cantilever FPDs investigated, the distal cantilever design was found to suffer less displacement and stresses than the mesial cantilever design under similar conditions of loading. The highest values for maximum principal stress in the cantilever FPDs were found within the connector between the pontic and the retainer, and within the periodontal ligament and adjacent bone on the aspect of the retainer away from the pontic.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.