Nanocrystals of MgO and CaO have been prepared by a modified aerogel/hypercritical drying/dehydration method. For nanocrystalline MgO (AP-MgO) surface areas ranged from 250 to 500 m 2 /g, whereas for AP-CaO 100-160 m 2 /g. These materials have been compared with more conventional (CP) microcrystalline samples of lower surface area with regard to (1) morphology (AP-samples (autoclave preparation) are tiny polyhedral crystallites, while CP-samples (conventional preparation) are larger, hexagonal platelets and cubes);(2) residual surface OH (AP-samples have less acidic OH, which are more isolated from each other; (3) acid gas adsorption (AP-samples adsorb more SO 2 and CO 2 at low pressures and room temperature and prefer monodentate rather than bidentate adsorption modes, but at higher pressures CP-samples adsorb more SO 2 and HCl apparently due to the formation of more well ordered multilayers); (4) destructive adsorption of organophosphorus compounds and chlorocarbons (AP-samples are superior due to higher surface areas and higher surface reactivities), and (5) very thin layers of transition metal oxides on the MgO and CaO nanocrystals that significantly enhance destructive adsorption capacities to the point where [M x O y ]AP-MgO and [M x O y ]-AP-CaO become stoichiometric in reaction with CCl 4 . The data are conclusive that the nanocrystals are more reactive than the microcrystals, and this is mainly attributed to morphological differences, including defects. However, intrinsic electronic effects due purely to "smallness" cannot be ruled out.

Room-temperature reactions of the chemical warfare agents VX, GD, and HD with nanosize CaO (AP-CaO), and HD with commercial CaO have been studied using solid-state MAS NMR. VX and GD hydrolyze to yield surface-bound complexes of nontoxic ethyl methylphosphonate and pinacolyl methylphosphonate, respectively. The kinetics are characterized by an initial fast reaction followed by a slower, diffusion-limited reaction. Similar behavior is observed for HD on either dried or hydrated AP-CaO and CaO. On partially hydrated AP-CaO (but not CaO), a rather fast steady-state elimination of HCl occurs after an induction period. This behavior is attributed to acid-catalyzed surface reconstruction (to regenerate fresh surface) and the formation of CaCl 2 , which is known to be more reactive than CaO. The product distribution for HD is about 80% divinyl sulfide and 20% thiodiglycol and/or sulfonium ions, which apparently reside as surface alkoxides. Such kinetic behavior was not evident for the common mustard simulant 2-chloroethyl ethyl sulfide (CEES) on partially hydrated AP-CaO, which exhibited only the typical fast/diffusion-limited reaction.

A new family of porous inorganic solids based on nanocrystalline metal oxides is discussed. These materials, made up of 4-7 nm MgO, CaO, Al2O3, ZnO, and others, exhibit unparalleled destructive adsorption properties for acid gases, polar organics, and even chemical/biological warfare agents. These unique sorption properties are due to nanocrystal shape, polar surfaces, and high surface areas. Free-flowing powders or consolidated pellets are effective, and pore structure can be controlled by consolidation pressures. Chemical properties can be adjusted by choice of metal oxide as well as by incorporating other oxides as monolayer films.

No abstract

Nanocrystals of magnesium oxide react with organophosphorus compounds at room temperature by dissociative chemisorption, which we term “destructive adsorption”. This process involves cleavage of PO and PF bonds (but not PC bonds) and immobilization of the resultant molecular fragments. These ultrafine powders have unusual crystalline shapes and possess high surface concentrations of reactive edge/corner and defect sites, and thereby display higher surface reactivity, normalized for surface area, than typical polycrystalline material. This high surface reactivity coupled with high surface area allows their use for effective decontamination of chemical warfare agents and related toxic substances. Herein data is presented for paraoxon, diisopropylfluorophosphate (DFP), and (CH3CH2O)2P(O)CH2SC6H5 (DEPTMP). Solid‐state NMR and IR spectroscopy indicate that all OR and F groups dissociate; this leaves bound PO4, F, and OR groups for paraoxon, DFP, and DEPTMP, respectively. For paraoxon, it was shown that one monolayer reacts. For DEPTMP, the OR groups dissociate, but not the PCH2SC6H5 group. The nanocrystalline MgO reacts much faster and in higher capacity than typical activated carbon samples, which physisorb but do not destructively adsorb these phosphorous compounds.

In the temperature range of 300-500 degrees C, solid nanocrystalline oxides react nearly stoichiometrically with numerous halocarbons, sulfur, and organophosphorus compounds. In some cases, the reaction efficiencies can be improved by the presence of a small amount of transition-metal oxide as catalyst; for example, Fe2O3 on CaO and mobile intermediate species such as FeCl3 or Fe(SO3)x are important in the catalytic process. Herein, a series of environmentally problematic compounds are discussed, including CCl4, COS, CS2, C2Cl4, CHCl3, CH2Cl2, CH3Cl, and (CH3O)2P(O)CH3. Nanocrystals of CaO coated with a thin layer of Fe2O3 (or other transition metals) =[Fe2O3]CaO, or intimately mixed =Fe2O3/CaO were compared with pure CaO. It was found that (a) the presence of a small amount of surface [Fe2O3] or other transition-metal oxide can have a marked effect on the destructive adsorption activity, (b) for some reagents, such as CCl4, C2Cl4, SO2 and others, the nanocrystalline CaO can react in stoichiometric amounts, especially if a transition-metal oxide catalyst is present, (c) although the reaction with dimethylmethylphosphonate is surface-limited, the nanocrystalline calcium oxide performed well and in high capacity, (d) nanocrystalline calcium oxide exhibits near stoichiometric activitywith several interesting sulfur-containing compounds, such as COS and CS2, (e) unfortunately, most fluorocarbons were not destructively adsorbed at 500 degrees C under the conditions employed; however, some of these can be effectively mineralized over the calcium oxide at higher temperatures. These compounds include C2F6, C3F6, C2ClF3, and CHF3, and (f) upon reaction, surface areas decreased considerably, from about 100 to about 10 m2/g. The results of these experiments further demonstrate that, with the proper choice of catalytic material, some solid-gas reactions can be engineered to be rapid and essentially stoichiometric.

No abstract

No abstract