Summary In this paper, a method composed of state of health (SOH) testing experiments and artificial intelligence simulation is proposed to carry out the study on the change of battery characteristic during its operation and generate mathematical models for the prediction of aging behaviour of battery. An experiment comprising of multidisciplinary parameters‐based SOH detection is conducted to study the battery aging characteristics from several aspects (ie, electrochemistry, electric, thermal behaviour and mechanics). In total, 200 sets of data (corresponding 200 charging/discharging cycles) are collected from the experiment. The data obtained from the first 150 cycles are employed in generation of the models. The result of sensitivity analysis based on the obtained genetic programming models shows that it is better to apply voltage value at the end of charging step, charging time and cycle number to predict the operational performance of the battery. The average predicted accuracy of model (without stress) is 94.52%, whereas the average predicted accuracy of model (with stress effect) is 99.42%. The proposed models could be useful for defining the optimised charging strategy, fault diagnosis and spent batteries disposal strategies.

The explosion of electric vehicles (EVs) has triggered massive growth in power lithium-ion batteries (LIBs). The primary issue that follows is how to dispose of such large-scale retired LIBs. The echelon utilization of retired LIBs is gradually occupying a research hotspot. Solving the issue of echelon utilization of large-scale retired power LIBs brings not only huge economic but also produces rich environmental benefits. This study systematically examines the current challenges of the cascade utilization of retired power LIBs and prospectively points out broad prospects. Firstly, the treatments of retired power LIBs are introduced, and the performance evaluation methods and sorting and regrouping methods of retired power LIBs are comprehensively reviewed for echelon utilization. Then, the problems faced by the scenario planning and economic research of the echelon utilization of retired power LIBs are analyzed, and value propositions are put forward. Secondly, this study summarizes the technical challenges faced by echelon utilization in terms of security, performance evaluation methods, supply and demand chain construction, regulations, and certifications. Finally, the future research prospects of echelon utilization are discussed. In the foreseeable future, technologies such as standardization, cloud technology, and blockchain are urgently needed to maximize the industrialization of the echelon utilization of retired power LIBs.

No abstract

Air‐cooling‐based battery thermal management system (BTMS) is a research hotspot for electric vehicles because of lower cost and simpler design. Past research works have immensely concentrated on the enhancement of heat removal from Li‐ion battery, but the minimum consideration has been given to minimize the parasitic power. In this paper, a novel procedure is proposed to predict the operating parameters (inlet velocity, working time of fan, and range of heat generation rates) of air‐cooling design for minimizing parasitic power and ensuring the battery temperature do not exceed the upper threshold limit simultaneously. Based on findings via computational fluid dynamics analysis, an empirical model of air‐cooling BTMS is further developed using an evolutionary approach of model selection criteria approximated genetic programming (MSC‐GP). The model is then optimized to determine operating parameters of air cooling which causes minimum parasitic power while keeping the average temperature of battery cells within the limit. Further, sensitivity analysis and parameter interaction (2D and 3D) analysis is also performed to study the effect and identify the contribution of various operating parameters on parasitic power. Operating time of fan has 49% influence on final temperature while inlet velocity has 36% influence only. However parasitic power is more sensitive to inlet velocity (77%) while operating time has 23% influence only. Finally, the optimal values of operating parameters for various heat generation rate per cell (function of discharge rate) are obtained. The optimized parasitic power was observed to be nonlinearly increasing with heat generation rate. Operating time of fan has 49% influence on final temperature while inlet velocity has 36% influence only. However, parasitic power is more sensitive to inlet velocity (77%) while operating time has 23% influence only.

No abstract

No abstract

Summary This study proposed an expert system approach on the basis of artificial intelligence (AI) in the modeling of cyclic voltammogram (CV) profiles of green tea extracts. AI approach of artificial neural networks is applied to generate the model phase‐plane portraits of current output versus applied voltage through CV scan cycles. The predicted current values were validated using experiments, and generic ability of approach was examined by testing on the CV scan cycles generated from Syzygium aromaticum and Citrus reticulate. It was concluded that AI approach can be employed to reveal stable point (cycle and voltage) in CV profiles for bioenergy applications.

Recovery of the vital metals from spent batteries using bioleaching is one of the commonly used method for recycling of spent batteries. In this study, a statistical based automated neural network approach is proposed for determination of optimum input parameters values in bioleaching of zinc‐manganese batteries. Experiments are performed to measure the recovery of zinc and manganese based on the input parameters such as energy substrates concentration, pH control of bioleaching media, incubating temperature, and pulp density. It was found that the proposed model based metal extraction models precisely estimated the yields of zinc and manganese with higher values of coefficient of determination of 0.94. Based on global sensitivity analysis, it was found that for the extraction of zinc, the most contributing parameters are pulp density and pH while for extraction of Mn the most contributing parameters are pulp density and incubating temperature. The optimum parameter values for maximum recovery of zinc and maximum recovery of manganese are determined using optimization method of simulated annealing. The optimum parameter values obtained for maximum recovery of Zn metal are as substrates concentration 32 g/L, pH 1.9 to 2.0, incubating temperature 30°C, pulp density 10%, and substrates concentration 32 g/L, pH 2.0, incubating temperature 35°C, pulp density 8% for maximum recovery of Mn.