Wearable pressure sensors have demonstrated great potential in detecting pulse pressure waves on the skin for the noninvasive and continuous diagnosis of cardiac conditions. However, difficulties lie in positioning conventional single-point sensors on an invisible arterial line, thereby preventing the detection of adequate signal amplitude for accurate pulse wave analysis. Herein, we introduce the spatiotemporal measurements of arterial pulse waves using wearable active-matrix pressure sensors to obtain optimal pulse waveforms. We fabricate thin-film transistor (TFT) arrays with high yield and uniformity using inkjet printing where array sizes can be customizable and integrate them with highly sensitive piezoresistive sheets. We maximize the pressure sensitivity (16.8 kPa −1 ) and achieve low power consumption (10 1 nW) simultaneously by strategically modulating the TFT operation voltage. The sensor array creates a spatiotemporal pulse wave map on the wrist. The map presents the positional dependence of pulse amplitudes, which allows the positioning of the arterial line to accurately extract the augmentation index, a parameter for assessing arterial stiffness. The device overcomes the positional inaccuracy of conventional single-point sensors, and therefore, it can be used for medical applications such as arterial catheter injection or the diagnosis of cardiovascular disease in daily life.

With the outbreak of new respiratory viruses and high mortality rates of pulmonary diseases, physiologically relevant models of human respiratory system are urgently needed to study disease pathogenesis, drug efficacy, and pharmaceutics. In this paper, a 3D alveolar barrier model fabricated by printing four human alveolar cell lines, namely, type I and II alveolar cells (NCI-H1703 and NCI-H441), lung fibroblasts (MRC5), and lung microvascular endothelial cells (HULEC-5a) is presented. Automated high-resolution deposition of alveolar cells by drop-on-demand inkjet printing enables to fabricate a three-layered alveolar barrier model with an unprecedented thickness of ≈10 µm. The results show that the 3D structured model better recapitulate the structure, morphologies, and functions of the lung tissue, compared not only to a conventional 2D cell culture model, as expected, but also a 3D non-structured model of a homogeneous mixture of the alveolar cells and collagen. Finally, it is demonstrated that this thin multilayered model reproduce practical tissue-level responses to influenza infection. Drop-on-demand inkjet-printing is an enabling technology for customization, scalable manufacturing, and standardization of their size and growth, and it is believed that this 3D alveolar barrier model can be used as an alternative to traditional test models for pathological and pharmaceutical applications.

We demonstrate high-performance and stable organic field-effect transistors (OFETs) using parylene-based double-layer gate dielectrics (DLGDs). DLGDs, consisting of parylene C as the upper layer and F as the lower layer, are designed to simultaneously provide good interface and bulk gate dielectric properties by exploiting the advantages of each gate dielectric. The structural effects of DLGDs are systematically investigated by evaluating the electrical characteristics and dielectric properties while varying the thickness ratio of each gate dielectric. The OFET with the optimized DLGD exhibits high performance and operational stability. This systematic approach will be useful for realizing practical electronic applications.

The algal cell immobilization is a commonly used technique for treatment of waste water, production of useful metabolites and management of stock culture. However, control over the size of immobilized droplets, the population of microbes, and production rate in current techniques need to be improved. Here, we use drop-on-demand inkjet printing to immobilize spores of the alga Ecklonia cava within alginate microparticles for the first time. Microparticles with immobilized spores were generated by printing alginate-spore suspensions into a calcium chloride solution. We demonstrate that the inkjet technique can control the number of spores in an ejected droplet in the range of 0.23 to 1.87 by varying spore densities in bioink. After the printing-based spore encapsulation, we observe initial sprouting and continuous growth of thallus until 45 days of culture. Our study suggest that inkjet printing has a great potential to immobilize algae, and that the ability to control the number of encapsulated spores and their microenvironments can facilitate research into microscopic interactions of encapsulated spores.

Electronic textiles, which are a combination of fabrics and electronics, can help realize wearable electronic devices by changing the rigidity of these textiles. We demonstrate organic light-emitting diodes (OLEDs) by directly printing the emitting material on fabric substrates using the nozzle-printing technique. Printing the emitting material directly on a fabric substrate with a rough surface is difficult. To address this, we introduce a planarization layer by using a synthesized 3.5 wt % poly­(vinyl alcohol) (PVA) solution. The sputtered ITO anode with the thermally annealed PVA planarization layer on a fabric substrate achieves a low sheet resistance in the range of 60–80 Ω/sq, whereas the ITO electrode without a PVA layer exhibits high sheet resistance values of 10–25 kΩ/sq. This result is because the thermally annealed PVA layer on the fabric surface has a uniform surface morphology and a water contact angle as high as 96°, thus acting as a protective layer with a waterproofing effect; in contrast, the water is completely absorbed on the rough surface without a PVA layer. The fabric-based OLEDs with a thermally annealed PVA layer exhibit a lower turn-on voltage of 3 V and higher luminance values of 5346 cd/m2 at 8 V compared with the devices without a PVA layer (7 V and 3622 cd/m2) at 18 V. These fabric-based OLEDs with a PVA planarization layer can be produced by the nozzle-printing process and can achieve selective patterning as well as direct printing of the emitting material and ITO sputtering on a fabric substrate; furthermore, they emit well even when it bent into a circle with a radius of 1 cm.