Çalışmada eriyik yığma modelleme (FDM) yöntemi ile 3B yazıcı kullanarak üretilen PLA numunelerin mekanik özelliklerden olan çekme dayanımına işlem parametrelerinin etkisi belirlenmesi amaçlanmıştır. Bu amaçla çalışmada işlem parametreleri olarak 2 farklı doluluk oranı (%20 ve %100), 3 farklı baskı hızı (100,150 ve 200 mm/s), 3 farklı nozul sıcaklığı (180, 205 ve 220°C) ve 3 farklı desen çeşidi (Cubic, Grid, Triangle) seçilmiştir. Çalışmada, %20 doluluk oranına göre %100 doluluk oranında daha yüksek çekme gerilmesi elde edilmiştir. %20 doluluk oranındaki numuneler kendi aralarında kıyaslandığında elde edilen en yüksek çekme gerilmesi değeri 220 0 C nozul sıcaklığında, 100 mm/s baskı hızında yapılan Grid desen çeşidinde 43.12 MPa olarak ölçülmüştür. %100 doluluk oranında ise en iyi sonuç 220 0 C de, 100 mm/s baskı hızında üretilen numunede 59.21 MPa çıkmıştır. Çalışmada %20 doluluk oranındaki numuneler için istatistik analiz yapılmıştır. Varyans analiz (ANOVA) yöntemi sonucu güven düzeyi %94,4 elde edilmiştir.
Objectives; Additive manufacturing includes systems that manufacture using many different methods. The most widely used and accessible methods can be listed as Fused Deposition Modelling (FDM), Selective Laser Sintering (SLS) and UV light assisted Stereolithography (SLA). Today, with these three methods, it is quite easy to produce thermoplastic products suitable for direct use in low quantities. In addition, the production success of the parts produced in geometric difficulties increases this demand. However, the biggest uncertainty encountered in the formation of the production demand for these methods is the lack of clear information about the strength limits, surface qualities and costs of the manufactured parts. However, the biggest uncertainty encountered in the formation of the production demand for these methods is the lack of clear information about the strength limits, surface qualities and costs of the manufactured parts. In order to eliminate this uncertainty, this study includes the comparison of three different production methods in terms of strength, surface roughness and material cost. For this purpose, samples produced using three different methods were subjected to tensile test and surface roughness was measured. In addition, production time and material cost calculations were made for each sample. At the end of the study, a maximum strength value of 57.67 N/mm2 and a minimum surface roughness value of 1.96µm were obtained. The most affordable sample in terms of material cost was obtained from resin material with $0.19.
ÖZET: Çalışmada eriyik yığma modelleme (FDM) yöntemi ile 3B yazıcı kullanarak üretilen PLA numunelerin mekanik özelliklerden olan çekme dayanımına işlem parametrelerinin etkisinin belirlenmesi amaçlanmıştır. Bu amaçla çalışmada işlem parametreleri olarak 2 farklı doluluk oranı (%20 ve %100), 2 farklı baskı hızı (100,130mm/sn), 2 farklı nozul sıcaklığı (180 ve 220°C) ve oval ve köşegen desen yapılarını içeren3 farklı desen çeşidi (Gyroid,Cross 3D ve Grid) seçilmiştir. Çalışmada, %20 doluluk oranına göre, %100 doluluk oranında daha yüksek çekme gerilmesi elde edilmiştir. %20 doluluk oranındaki numuneler kendi aralarında kıyaslandığında elde edilen en yüksek çekme gerilmesi değeri 220 0 C nozul sıcaklığında, 100 mm/s baskı hızında üretilen Grid desen çeşidinde 38.76 MPa olarak ölçülmüştür. Çalışmada %20 doluluk oranındaki numuneler için istatistik analiz yapılmıştır. Varyans analiz (ANOVA) yöntemi sonucu güven düzeyi %96 elde edilmiştir. Özgül dayanım açısından kıyaslama yapıldığında ise 5,893 MPa/gr özgül dayanıma sahip tam dolu parçaya en yakın desenin 5.458 MPa/gr değeri ile Cross 3D deseni olduğu belirlenmiştir.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.