The startup of rocket engine turbopumps is generally performed only in a few seconds. It implies that these pumps reach their nominal operating conditions after only a few rotations. During these first rotations of the blades, the flow evolution in the pump is governed by transient phenomena, based mainly on the flow rate and rotation speed evolution. These phenomena progressively become negligible when the steady behavior is reached. The pump transient behavior induces significant pressure fluctuations, which may result in partial flow vaporization, i.e., cavitation. An existing experimental test rig has been updated in the LML Laboratory (Lille, France) for the startups of a centrifugal pump. The study focuses on the cavitation induced during the pump startup. Instantaneous measurement of torque, flow rate, inlet and outlet unsteady pressures, and pump rotation velocity enable to characterize the pump behavior during rapid starting periods. Three different types of fast startup behaviors have been identified. According to the final operating point, the startup is characterized either by a single drop of the delivery static pressure, by several low-frequency drops, or by a water hammer phenomenon that can be observed in both the inlet and outlet of the pump. A physical analysis is proposed to explain these three different types of transient flow behavior.

In the present study, the flow through the fan stage of a high bypass ratio turbofan at windmill is studied numerically. First, steady mixing plane simulations are validated against detailed experimental engine test-bed measurements, at several locations within the fan stage and close to the core/bypass flow splitter. Good agreement between the numerical and experimental results is obtained. A local flow analysis is proposed, evidencing several characteristics of the flow in windmilling: in the rotor, the size of the separation zone is found to increase from hub to tip, and in the stator, massive flow separation occurs at mid-span, which leads to the formation of two streamwise counter-rotating vortices. Then, the Nonlinear Harmonic (NLH) method is applied to a section (at 70 % of the relative span) of the fan stage. A modal analysis is performed, showing a specific behavior at windmill: the massively separated flows in the rotor and the stator entail strong rotor/stator interactions modes. Finally, the unsteady flow pattern is examined: the velocity defect of the rotor wake, which periodically increases the flow angle on the stator, is shown to trigger a periodic movement of the reattachment point at the trailing edge of the stator, associated with vortex shedding from the lower side of the vane. The implication of this qualitative flow behavior on the method to extract CFD results for comparisons with experiments is discussed.

The present work is a contribution to understanding the windmilling operation of low-speed fans. Such an operating situation is described in the literature, but the context (mainly windmilling of aero-engines) often involves system dependence in the analysis. Most of the time, only regimes very close to the free-windmilling are considered. A wider range is analyzed in the present study, since the context is the examination of the energy recovery potential of fans. It aims at detailing the isolated contribution of the rotor, which is the only element exchanging energy with the flow. Other elements of the system (including the stator) can be considered as loss generators and be treated as such in an integrated approach. The evolution of the flow is described by the use of theoretical and experimental data. A theoretical model is derived to predict the operating trajectories of the rotor in two characteristic diagrams. A scenario is proposed, detailing the local evolution of the flow when a gradual progression toward free and load-controlled windmilling operation is imposed. An experimental campaign exerted on two low-speed fans aims at the analysis of both the local and global aspects of the performance, for validation. From a global point of view, the continuity of the operating trajectory is predicted and observed across the boundary between the quadrants of the diagrams. The flow coefficient value for the free-windmilling operation is fairly well predicted. From a local point of view, the local co-existence of compressor and turbine operating modes along the blade span is observed as previously reported. It is further demonstrated here that this configuration is not exclusive to free-windmilling operation and occurs inside a range that can be theoretically predicted. It is shown that for a given geometry, this local topology strongly depends on the value of the flow coefficient and is very sensitive to the inlet spanwise velocity distribution.

This paper aims to perform a drag breakdown of an airfoil and a wing by using the exergetic method. Moreover, a new far-field wave anergy extraction method is presented. The resulting exergetic drag curves are proposed as additional characteristic curves for external aerodynamic assessment of airfoils or any other bodies. CFD analyses of a NACA 0012 airfoil and a rectangular wing at subsonic and transonic conditions were used as test cases to present the concept. This new approach allows to deeply understand the aerodynamic behavior of a body and provides an alternative point of view to the classical near-field and far-field based drag curves.

No abstract

International audienceThe start-up of rocket engine turbopumps is generally performed in a few seconds or even less. It implies that these pumps reach their nominal operating conditions after a few rotations only. During the start-up, the flow evolution within the pump is governed by transient phenomena, based mainly on the flow rate and rotation speed increase. Significant pressure fluctuations, which may result in the development of cavitation, are observed. A centrifugal impeller whose transient behavior during start-ups has been detailed in a previous publication is considered. Three different cases of fast start-ups have been identified according the final operating point (Duplaa et al., 2010, "Experimental Study of a Cavitating Centrifugal Pump During Fast Start-Ups," ASME J. Fluids Eng., 132(2), p. 021301). The aim of this paper is to analyze the evolution during the start-ups of the local amount of vapor in the blade to blade channels of the pump by fast X-ray imaging. This technique has enabled to calculate the time-evolution of the fluid density within the pump, which appears to be correlated with pressure time-evolutions. For each investigated start-up, X-ray measurements have been performed at three different sections of the impeller height. For each investigated start-up and section tested, measurements have been performed for several initial positions of the impeller, to estimate the measurement uncertainty, and to obtain records from different beam angles, like in tomography

The objective of this paper is development and application of a methodology for preliminary analysis of variable pitch fan (VPF), both as a separate component and as a module integrated into a short-medium range geared turbofan engine developed within European FP7 project ENOVAL. For this purpose, a high bypass ratio two spool geared turbofan engine model was constructed in software PROOSIS. A VPF performance modelling methodology was then developed using 3D steady RANS CFD produced fan maps as baseline; the CFD maps characterised five discrete fan pitch angle settings. In order to represent those maps in PROOSIS and add the pitch angle as a degree of freedom, they were transformed into the Map Fitting Tool (MFT) reference frame. Once the complete VPF turbofan model was in place, engine mission optimisation experiments were carried out. The resulting performance is characterised by a good capability to control the fan surge margin, without degrading the engine fuel consumption.

No abstract