Additive manufacturing is especially suitable for complex-shaped 3D parts with integrated and optimized functionality realized by filigree geometries. Such designs benefit from low safety factors in mechanical layout. This demands ductile materials that reduce stress peaks by predictable plastic deformation instead of failure. Al–Cu wrought alloys are established materials meeting this requirement. Additionally, they provide high specific strengths. As the designation “Wrought Alloys” implies, they are intended for manufacturing by hot or cold working. When cast or welded, they are prone to solidification cracks. Al–Si fillers can alleviate this, but impair ductility. Being closely related to welding, Laser Beam Melting in Powder Bed (LBM) of Al–Cu wrought alloys like EN AW-2219 can be considered challenging. In LBM of aluminium alloys, only easily-weldable Al–Si casting alloys have succeeded commercially today. This article discusses the influences of boundary conditions during LBM of EN AW-2219 on sample porosity and tensile test results, supported by metallographic microsections and fractography. Load direction was varied relative to LBM build-up direction. T6 heat treatment was applied to half of the samples. Pronounced anisotropy was observed. Remarkably, elongation at break of T6 specimens loaded along the build-up direction exceeded the values from literature for conventionally manufactured EN AW-2219 by a factor of two.

No abstract

No abstract

No abstract

The progressively more demanding needs of emissions and costs reduction in the transportation industry are pushing engineers towards the use of increasingly lightweight structures. This goal can be achieved only if dissimilar and/or new materials, including polymers and composites, are joined together to create complex structures. Conventional fusion welding processes have often been proven inadequate to this task because of the high heat input reducing the joint mechanical properties or even making the joining process impossible. Joining by forming technologies take advantage on the plastic deformation to create sound joints out of even very dissimilar materials. Over the last 25 years, several new processes, with increasing potential in effectively joining virtually every structural material, have been invented and developed. In the paper, a comprehensive overview of the most utilized joining by forming processes is given. For each process, an analysis of the current research trends and hot topics is provided, highlighting strengths and weaknesses for industrial applications.

No abstract

Shear-clinching has proven to be a suitable technology for joining of high-strength materials. However, the mechanical properties of the upper joining partner are limited due to the high strains, which occur during the process. Therefore, shear-clinching of the high-strength aluminum alloy AA7075 in the T6 temper is not possible. Yet, the mechanical properties of hardenable alloys of the 7000 series can be influenced by a heat treatment. Thus, within the scope of this work, the joinability of the high-strength alloy AA7075 in shear-clinching processes in dependance of its temper is investigated. The as fabricated state F, the artificially aged T6 temper, a paint baked state and the naturally aged T4 temper are compared to the fully solution annealed W temper as well as to a retrogression heat-treated state. For retrogression heat treatment, a laser is used as heat source, heating up the alloy for a short term in order to only partially dissolve precipitations. The resulting mechanical properties are determined with uniaxial tensile tests. Moreover, the influence of the mechanical properties of AA7075 on the shear-clinching process, the joint formation and the resulting joint strength is analyzed.

The newly developed joining-by-forming technology “shear-clinching”, features a potentially single-stage process for joining UHSS without requiring any additional elements. Foundational studies have focused on the functionality of shear-clinching at a one-element sample. To ensure the safety of the industrial application of the shear-clinching technology, an investigation with component-like samples with several joints is required. This paper presents a detailed analysis of the material behaviour during the shear-clinching process with multi-element specimens to evaluate the influence of the neighbouring joints. In order to describe the influence of the neighbouring joints, the deformations resulting from the bending and material displacement are recorded without contact after the joining process: locally around the joining point and globally over the entire sample size. To minimize such bending effects, a tool-sided adaptation is provided. The results show the high potential of shear-clinching joining by UHSS and give further recommendations for future multi-material application.