Self-standing films (45-μm thick) of native cellulose nanofibrils (CNF) were synthesized and characterized for their piezoelectric response. The surface and the microstructure of the films were evaluated with image-based analysis and scanning electron microscopy (SEM). The measured dielectric properties of the films at 1 kHz and 9.97 GHz indicated a relative permittivity of 3.47 and 3.38 and loss tangent tan  of 0.011 and 0.071, respectively. The films were used as functional sensing layers in piezoelectric sensors with corresponding sensitivities of 4.7 to 6.4 pC/N in ambient conditions. This piezoelectric response is expected to increase remarkably upon film polarization resulting from the alignment of the cellulose crystalline regions in the film. The CNF sensor characteristics were compared with those of polyvinylidene fluoride (PVDF) as reference piezoelectric polymer. Overall, the results suggest that CNF is a suitable precursor material for disposable piezoelectric sensors, actuator or energy generators with potential applications in the fields of electronics, sensors and biomedical diagnostics.

Some bacterial strains such as Komagataeibacter xylinus are able to produce cellulose as an extracellular matrix. In comparison to wood-based cellulose, bacterial cellulose (BC) holds interesting properties such as biodegradability, high purity, water-holding capacity, and superior mechanical and structural properties. Aiming toward improvement in BC production titer and tailored alterations to the BC film, we engineered K. xylinus to overexpress partial and complete bacterial cellulose synthase operon that encodes activities for BC production. The changes in cell growth, end metabolite, and BC production titers from the engineered strains were compared with the wild-type K. xylinus. Although there were no significant differences between the growth of wild-type and engineered strains, the engineered K. xylinus strains demonstrated faster BC production, generating 2-4-fold higher production titer (the highest observed titer was obtained with K. xylinus-bcsABCD strain producing 4.3 ± 0.46 g/L BC in 4 days). The mechanical and structural characteristics of cellulose produced from the wild-type and engineered K. xylinus strains were analyzed with a stylus profilometer, in-house built tensile strength measurement system, a scanning electron microscope, and an X-ray diffractometer. Results from the profilometer indicated that the engineered K. xylinus strains produced thicker BC films (wild type, 5.1 μm, and engineered K. xylinus strains, 6.2-10.2 μm). Scanning electron microscope revealed no principal differences in the structure of the different type BC films. The crystallinity index of all films was high (from 88.6 to 97.5%). All BC films showed significant piezoelectric response (5.0-20 pC/N), indicating BC as a promising sensor material.

No abstract

No abstract

The ongoing revolution of touch‐based user interfaces sets new requirements for touch panel technologies, including the need to operate in a wide range of environments. Such touch panels need to endure moisture and sunlight. Moreover, they often need to be curved or flexible. Thus, there is a need for new technologies suitable, for example, for home appliances used in the kitchen or the bathroom, automotive applications, and e‐paper. In this work, the development of transparent and flexible touch panels for moist environments is reported. A piezoelectric polymer, poly(vinylidene difluoride) (PVDF), is used as a functional substrate material. Transparent electrodes are fabricated on both sides of a PVDF film using a graphene‐based ink and spray coating. The excellent performance of the touch panels is demonstrated in moist and underwater conditions. Also, the transparent device shows very small pyroelectric response to radiative heating in comparison to a non‐transparent device. Solution processable electrode materials in combination with functional substrates allow the low‐cost and high‐throughput manufacturing of touch panels using printing technologies.

Wrist PPG signal is widely used in optical heart rate monitors. Based on the results obtained in this study, wrist PPG signal may be used also for PAT calculation. The use of PAT for blood pressure estimation still has challenges, but PAT as such could be used as an interesting indicator of vascular health.

No abstract

No abstract