The effect of boron addition into Fe–28Al–5Si–X (X = -, 2Mo, or 2Ti) on the structure and high-temperature yield stress was investigated. Generally, the alloying of binary Fe3Al-type iron aluminides by silicon significantly improves high-temperature mechanical properties by solid-solution strengthening. On the other hand, the workability and ductile properties at room or slightly elevated temperatures get worse with the increasing silicon content. Boron alloying together with titanium or molybdenum alloying is one of the ways to improve the workability of this type of alloy and, at the same time, ensure the formation of a sufficient amount of secondary phase particles required for effective strengthening. In this paper, the influence of 1 at. % of boron on high-temperature yield stress is evaluated in response to structural changes and compared with results obtained previously on the same type of alloy (Fe–28Al–5Si–2X, X= -, Mo, or Ti) but without boron alloying. It can be concluded that the network structure of borides of refractory metals formed due to boron alloying works more effectively for alloy hardening at higher temperatures than a mixture of silicides and carbides present in the boron-free alloy of the same composition.
Temperature cycles generated during welding have a significant effect on the changes in the HAZ of welds, regardless of whether these are changes in structure or mechanical properties; however, it is problematic to obtain temperature cycles with sufficient accuracy across the entire HAZ so that they can be generally taken and used in welding simulations and for real experiments of processes occurring in HAZ. In particular, for a study in a specific location, it is important to know the maximum temperature of the cycle and the cooling rate defined mainly by the parameter t8/5. No studies in which anybody tries to find a mathematical description defining the basic parameters of temperature cycles in the HAZ could be found in the performed research. Therefore, the study presented in this paper results in a mathematical description defining the dependence of achieved maximum temperature on the distance from the fusion line in the HAZ of S460MC welds and with heat input values in the interval from 8 to 14 kJ·cm−1. Moreover, this paper presents the influence of heat input value on the weld pool geometry, including the effect of heat input value on grain coarsening in the highly heated HAZ.
Concerning the increasingly widespread utilization of the finite element method (FEM), the concept of the so-called virtual factory is also gaining ground, and not only in the engineering industry. This approach does not use numerical simulations of individual production technologies separately but treats the entire production process as a chain of interrelated technologies. Thus, the output data from one technology is taken as input data for the following technology. The resulting thermal and mechanical effects are then not only dealt with within one technology but always comprehensively within the production process. In the consideration of the loading and subsequent service lives of manufactured components, values of residual stresses are one of the very important characteristics. For these reasons, this paper deals with the effect of residual stresses’ magnitude and distribution during the formation and the final springback of the seamed pipe end section with and without respect to the influence of the preceding welding. The resulting residual stress values from numerical simulations are subsequently compared with the actual values of residual stresses experimentally measured using X-ray diffraction.
This paper presents the results of research dealing with assessing the welding effect (temperature–stress cycles) on the residual stresses in these steels. Residual stresses, remaining in the material after technological processing, pose a risk, especially at the areas of local stress peaks. During the real welding, residual stresses achieve their highest values in the heat-affected zone (HAZ), which is very narrow and therefore quite problematic to be studied in detail. Therefore, a methodology of temperature–stress physical simulations has been developed to study residual stresses in the HAZ over a 6.5 times larger section of the test sample. Thus, temperature cycles corresponding to the real welding were applied to the samples in the thermo-mechanical simulator, Gleeble 3500. Subsequently, the residual stresses were determined by the X-ray diffraction method. At the same time, the influence of annealing temperature on the residual stress reduction and redistribution was also investigated. Obtained results were compared and discussed with the similar studies about HSLA and duplex steels.
Fine-grained steels, which belong to the HSLA (High-Strength Low-Alloy) group of steels, are increasingly used for parts of statically and dynamically loaded constructions. Due to the thermal effect of welding, combined with the inherent stiffness and clamping stiffness of the part, residual stresses are generated in the HAZ (heat-affected zone) which affect the fatigue life of the sub-weld and the entire construction. In this article, a specific temperature cycle measured during welding is used, which, together with a defined clamping stiffness, produces residual stresses of a defined shape and value in the sample. Subsequently, the effect of these stresses on the fatigue life on the change of the S–N curve compared to the annealed material, is assessed. Temperature cycles were applied using a Gleeble 3500 and the residual stresses were analyzed by X-ray diffraction (XRD). It was found that the effect of residual stresses decreased the fatigue strength by 33% compared to the annealed material. It was further found that by using annealing to reduce the residual stresses, it is possible to restore the fatigue life of S700MC steel to the original value of the base material.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.