The welding of fine-grained steels is a very specific technology because of the requirement for the heat input limit value. Applying temperature cycles results in an intense grain growth in a high-temperature heat-affected zone (HAZ). This has a significant effect on the changing of strength properties and impact values. The intensity of grain coarsening in the HAZ can be predicted based on the experimentally determined activation energy and material constant, both of which define grain growth kinetics. These quantities, together with real measured welding cycles, can be subsequently used during experiments to determine mechanical properties in a high-temperature HAZ. This paper shows a methodical procedure leading to the obtainment of the material quantities mentioned above that define the grain growth, both at fast and slow temperature cycles. These data were used to define the exposure temperature and the soaking time in a vacuum furnace to prepare test samples with grain sizes corresponding to the high-temperature HAZ of welded joints for the testing procedures. Simultaneously, by means of the thermo-mechanical simulator Gleeble 3500, testing samples were prepared which, due to a temperature gradient, created conditions comparable to those in the HAZ. The experiments were both carried out with the possibility of free sample dilatation and under a condition of zero dilation, which happens when the thermal expansion of a material is compensated by plastic deformation. It has been found that shape of the temperature cycle, maximal achieved cycle temperature, cooling rate, and, particularly, the time in which the sample is in the austenite region have significant effects on the resulting change of properties.

Fine-grained steels belong to the progressive materials, which are increasingly used in the production of welded structures subjected to both static and dynamic loads. These are unalloyed or microalloyed steels hardened mainly by the grain-boundary strengthening mechanism. Such steels require specific welding procedures, especially in terms of the heat input value. At present, there are studies of the welding influence on the change of thermomechanically processed steels’ mechanical properties, however mainly under static loading. The paper is therefore focused on the assessment of the welding effect under dynamic loading of welded joints. In the experimental part was determined the influence of five different heat input values on the change of weld fatigue life. As a result, there is both determination of five S-N curves for the double-sided fillet welds from the thermomechanically processed fine-grained steel S460MC and the quantification of the main influences reducing the fatigue life of the joint.

No abstract

Our workplace, Technical University of Liberec, is currently engaged in research and production of cellular metal systems. Basically, cellular metal systems are materials with lower density. It is a research in the field of mechanical engineering that is focused on the development of new materials. In general, many methods have been developed for the production of cellular metal systems, e.g. by BANHART [2] or ASHBY [4]. At their production, the direct gassing of molten metals (mostly aluminium ones) or gassing by the powder agents (e.g. specially formulated aluminium powders) are mostly used. Depending on the manufacturing method, a cellular system with open or closed cells can be obtained. The most commonly used metal is aluminium and its alloys. We are currently focusing on the production of porous aluminium by using sodium chloride. Sodium chloride occupies regular sites in the aluminium material and thus contributes to the aluminium porosity. After solidification of the aluminium, sodium chloride is dissolved in water. Sodium chloride is relatively inert to the aluminium and together with it, has a favourable density (2160 kgm-3) compared to the aluminium density (2700 kgm-3). The values of these physical quantities were observed on the produced aluminium test specimens having  60 x 10 mm: relative density of porous system REL; porosity of metal system P; amount of solid phase system volume fraction VPM; density of porous metal system PM and porous material Young's modulus of elasticity EPM.

This article deals with a comprehensive study of the processing and mechanical properties of the ceramic material Al2O3 on Fused Filament Fabrication technology (FFF). It describes the basic input analyses of the material, such as TGA, FTIR, and MVR. These analyses enabled the design and testing of process parameters for the 3D printing of parts. The article also presents the post-processes, including the technological parameters required to finalize parts made from this material, i.e., chemical debinding in acetone at elevated temperatures + thermal debinding and sintering. The microhardness was measured on the processed samples, depending on the density of the inner filling. The resulting hardness had an almost linear relationship between the percentage of filler (20–40–60–80–100%) and the resulting microhardness (1382–2428 HV10). Flexural strength was also measured on the test specimens with different degrees of internal filling (80–90–100%). However, inner filling do not affect the flexural strength (316.12–327.84–331.61 MPa). The relative density of the final parts was measured on a ZEISS METROTOM 1500 CT machine and reached 99.54%.

No abstract

The effect of the computational model and mesh strategy on the springback prediction of the thin sandwich material made of micro-alloyed steel was investigated in this paper. To verify the chosen computational strategy, a comparison of the experimentally obtained specimen (U-bending) with the FEA result was performed. The Vegter yield criterion combined both with the isotropic and kinematic hardening law was used for the calculation. In addition, the effect of the deformation mesh element (surface and volume) on the accuracy of the springback prediction was investigated. It was concluded that the choice of the volume deformation mesh does not significantly improve the accuracy of the results. Moreover, it is quite a time-consuming approach. The much greater influence was monitored by concerning the selection of hardening law, where the anisotropic one was more suitable to be used on the springback prediction of a given sandwich material.

The creation of the heterogeneous joints at materials with the different physical and mechanical properties is always problematic. As one of methods by which can be achieved very good results is there a diffusion welding. The aim of paper is to show the possibilities of diffusion welding utilization at creation the heterogeneous joints between Titan grade 2 and high-alloyed austenitic steel AISI 316L. The fundamental theory of diffusion and also scheme and realization of experimentally created diffusion welds in the thermal-mechanical simulator Gleeble® 3500 is described in the article. Furthermore, procedure of technological parameters selection when optimization of heterogeneous joint strength properties including metallographic evaluation are taken into account, are also presented.