Memperbaiki Mushola Al Khoiriyah di Kampung Lio adalah satu kegiatan sehingga keberadaan mushola tersebut lebih layak digunakan sebagai prasarana beribadah umat muslim di lingkungan RT.05/RW.09, Kelurahan Bojong Pondok Terong, Kecamatan Cipayung, Kota Depok. Terutama ketika musholla digunakan shalat tarawih pada bulan Ramadhan. Pada kegiatan Pengabdian pada Masyarakat kali ini untuk Prodi Konstruksi Gedung Politeknik Negeri Jakarta memperbaiki ruang penunjang mushola terutama perbaikan tempat wudhu dan toilet. Lingkup pekerjaan pada perbaikan dinding penahan tanah dan lantai tempat wudhu dan toilet. Dengan selesainya pekerjaan perbaikan tersebut, akan tersedia prasarana Mushola yang dapat meningkatkan ketakwaan serta keimanan kepada Tuhan Yang Maha Esa di lokasi yang dimaksud. Target khusus dari kegiatan ini adalah menyempurnakan fasilitas fisik mushola Al Khoiriyah di Kampung Lio, RT.05/RW.09, Kelurahan Bojong Pondok Terong, Kecamatan Cipayung, Kota Depok. Metode yang digunakan untuk mencapai tujuan di atas adalah Tim pengabdian masyarakat Program Studi Konstruksi Gedung, Jurusan Teknik Sipil, Politeknik Negeri Jakarta bekerjasama dengan warga secara bergotong royong melakukan perbaikan mushola tersebut. Kegiatan ini direncanakan selesai dalam waktu 2 bulan.
The material of ceiling cover in a room could be plywood, asbestos, gypsum, glass reinforce cement, et cetera. This research was triggered by the large number of newspaper waste which was improperly dumped and caused contamination to the environment. Newspaper pulp is produced by finely grinding the newspaper or by crushing the newspaper in wet condition using blender. This pulp is then mixed with Portland cement and formed as wanted. In this research, the composition of Portland cement to newspaper pulp are 50:50; 55:45 and 60:40 and formed into board with the thickness of 10 mm. The objective of the research is to discover the proper proportion of newspaper pulp and Portland cement to obtain the consistent quality. It is intended that this research discover the substituting material for gypsum ceiling. This research was tested in the PNJ Civil Engineering Laboratory. There were some variants of test to obtain the proportion of Portland cement and newspaper pulp which conforms to standards. There were some stage of material test, which were absorption test, tension strenght test, and flexural strength test. The data processing was done by averaging the value of test result. The absorption and fracture strength showed that the greater the proportion of cement, the higher the fracture strength. In this research, it was obtained in the proportion of 60:40 with the value of 20,497 kg/cm2. While the absorption test showed that the increase in proportion of cement reduced the water absorption. In this research, it was obtained in the composition of 60:40 with the amount of 48.93%.Keywords : ceiling, newspaper waste,composition, testABSTRAKBahan penutup plafon suatu ruangan dalam bangunan gedung dapat berupa kayu lapis/ tripleks, asbes, gypsum, glass reinforce cement (GRC) dan sebagainya. Penelitian ini dilatarbelakangi karena banyaknya limbah koran yang dibuang sembarangan dan saat ini yang dapat menyebabkan pencemaran lingkungan. Bubur kertas koran dapat dibuat dengan cara menumbuk halus atau dihancurkan menggunakan mesin blender dalam keadaan basah yang kemudian dicampur menggunakan bahan semen portland dan dicetak dapat menjadi bentuk sesuai yang diinginkan. Dalam penelitian ini komposisi antara semen portland dengan bubur kertas koran 50:50; 55:45 dan 60:40 dicetak dan dibentuk menjadi papan dengan ketebalan 10 mm. Tujuan dari penelitian ini adalah untuk mencari perbandingan yang sesuai antara bubur kertas koran dengan semen portland, agar mendapatkan kualitas sesuai . Penelitian ini diharapkan dapat memeproleh bahan pengganti penutup plafon dari bahan gypsum. Penelitian ini di uji di laboratorium teknik sipil PNJ dan pengujian ini dibuat beberapa varian seperti tersebut di atas untuk mendapatkan perbandingan antara semen potland dan bubur kertas koran yang sesuai dengan standar . Ada beberapa tahap pengujian bahan yaitu melalui pengujian daya serap air, pengujian kuat tarik ,pengujian kuat lentur. Teknik pengolahan data yang dilakukan dengan mencari rata-rata dari hasil pengujian yang telah dilakukan. Dari hasil pengujian daya serap air dan kuat patah menunjukkan bahwa semakin besar kadar semen kuat patah semakin meningkat, dalam hal ini dicapai pada komposisi 60:40 sebesar 20.497 kg/cm2 sedangkan untuk daya serap air menunjukkan bahwa semakin besar kadar semen daya serap air mengalami penurunan, dalam hal ini dicapai pada komposisi 60:40 sebesar 48.93%Kata Kunci : Plafon, kertas koran, semen, komposisi, pengujian
Berdasarkan hasil wawancara dan pengamatan tim Pengabdian Kepada Masyarakat, ditemukan beberapa permasalahan yang sangat krudensial mengenai keberadaan Mushola Al Hidayah Kampung Pondok Manggis yang sudah tidak layak digunakan sebagai prasarana beribadah umat muslim di lingkungan RT.03/RW.04, Desa Bojong Baru, Kecamatan Bojong Gede, Kabupaten Bogor. Diantaranya yaitu belum terlaksananya pengecoran atap, pemasangan dinding pembatas, plesteran dinding dan pemasangan keramik dinding serta lantai tempat wudhu. Untuk itu perlu dilakukan perbaikan Mushola Al Hidayah, terutama perbaikan pada atap toilet, plester dinding toilet, mengganti pintu toilet, pemasangan keramik dinding dan lantai tempat wudhu, serta pemasangan dan plester dinding penyekat. Dalam mencapai tujuan diatas maka tim Pengabdian Kepada Masyarakat Program Studi Konstruksi Gedung, Jurusan Teknik Sipil, Politeknik Negeri Jakarta, bekerjasama dengan warga secara bergotong royong melakukan perbaikan Mushola tersebut yang dilaksanakan pada tanggal 6 dan 13 Oktober 2018. Dimana target khusus dari kegiatan ini adalah menyempurnakan kondisi fisik Mushola Al Hidayah Kampung Pondok Manggis, RT.03/RW.04, Desa Bojong Baru, Kecamatan Bojong Gede, Kabupaten Bogor. Dengan selesainya pekerjaan tersebut maka tersedia prasarana Mushola yang memadai guna meningkatkan ketakwaan serta keimanan kepada Tuhan Yang Maha Esa.
This research is conducted to study the physical and mechanical characteristic of mortar. The mortar used has a cement-sand volume ratio of 1 : 5. Then, PVAc White Glue is added to this mixture with various percentages of 0. 3.0, 6.0, 9.0, 12.0, and 15.0 percent of cement weight. The water-cement ratio decreased as the increase of white glue PVAc percentage. The maximum and minimum water-cement ratio value of 1.12 and 0.717 were obtained respectively on the samples with 0% and 15.0% PVAc. The average decreasing of water-cement ratio was 0.081 on every 3.0% addition of PVAc. The addition of white glue resulted a production of air void and caused agglomeration on mortar and the mortar became elastic, thus it reduced the ease of compacting the mortar mixture. The characteristic of the mortar that was hard to be compacted and the compaction that was done manually resulted in the unevenness unstandardized level of compactness. The results indicated a varied of fluctuating value with low confidence level, thus the tendency and the influence of the PVAc addition were hard to be determined. From the test on the normal condition (N), the characteristics were hard to be determined were the decrease of unit weight with R2 = 0.203; the increase of compressive strength with R2 = 0.058; the increase of splitting tensile strength with R2 = 0.145; the decrease of bonding strength with R2 = 0.007, the decrease of surface abrasion resistance with R2 = 0.0001, and the decrease of 10-minutes water uptake with R2 = 0.185. While, the other characteristics of normal condition samples (N) with better confidence value were the decrease of flexural strength with R2 = 0.651; the modulus of elasticity with R2 = 0.61; and the decrease of 24-hours water uptake with R2 = 0.574. The mortar was difficult to be compacted, and a nonstandard compaction method were suspected to caused of unsatisfactory result of this research. ABSTRAK Penelitian ini dilaksanakan untuk mengetahui sifat fisik dan mekanik mortar dengan perbandingan volume 1 semen : 5 pasir menggunakan bahan tambah lem putih PVAc sebanyak 0,0; 3,0; 6,0; 9,0; 12,0 dan 15,0 persen dari berat semen. Pengamatan sifat fisik meliputi faktor air semen, nilai sebar, berat isi dan serapan air. Pengamatan terhadap sifat mekanik meliputi kuat tekan, kuat tarik, kuat lentur, kuat lekat, ketahanan abrasi permukaan mortar dan modulus elastisitas Faktor air semen (f a s) semakin menurun seiring bertambahnya persentase lem putih PVAc, f a s terbesar 1,12 dan terkecil 0,717 masing-masing diperoleh dari kadar PVAc 0,0% dan 15,0%. Penurunan fas rata-rata sebesar 0,081 pada setiap penambahan lem putih PVAc 3,0%. Penambahan lem putih menimbulkan gelembung udara dan mortar menjadi menggumpal dan elastis, sehingga mengakibatkan mortar sulit dipadatkan. Pemadatan dilakukan secara manual sehingga tidak diperoleh tingkat kepadatan yang sempurna yang akan berpengaruh terhadap hasil pengujian-pengujian selanjutnya. Hasil pengujian menunjukkan nilai yang variatif dan fluktuatif dan tingkat kepercayaan yang rendah, sehingga sulit untuk ditetapkan pengaruh dan kecenderungannya. Dari hasil pengujian kondisi normal atau kering (N) yang sulit untuk ditetapkan pengaruhnya adalah berat isi berupa penurunan dengan R2= 0,203, kuat tekan berupa kenaikan dengan R2 = 0,058, kuat tarik berupa kenaikan dengan R2 = 0,145, kuat lekat berupa penurunan dengan R2 = 0,007, ketahan abrasi permukaan berupa penurunan dengan R2 = 0,0001dan serapan air 10 menit berupa penurunan dengan R2 = 0,185. Hasil pengujian kondisi normal atau kering (N) dengan tingkat kepercayaan lebih baik adalah kuat lentur berupa penurunan dengan R2 = 0,651, modulus elastisitas dengan R2 = 0,61 dan serapan air 24 jam berupa penurunan dengan R2 = 0,574. Sifat mortar yang sulit dipadatkan dan metode pemadatan yang tidak standard diduga menjadi penyebab diperolehnya hasil pengujian yang tidak memuaskan. Kata kunci: mortar, lem putih, poly vinyl acetate, polivinil asetat, PVAc, persentase
Mechanic characteristics of hard mortar are: compressive strength, flexural strength, tensile strength, and adhesion power. In the meantime, at Building Material Laboratory of Civil Engineering, State Polytechnic of Jakarta, test of tensile strength and adhesion power of mortar cannot be conducted because of the absence of the test equipment.This research aims to provide electric motor-powered equipment for tensile strength test of mortar in order to complete the equipment at Building Material Laboratory of Civil Engineering, State Polytechnic of Jakarta. The particular aim of the research is to make prototype of mortar tensile strength test equipment.In this research a prototype of motor-powered mortar tensile strength test equipment and the specimens, to test the performance of the equipment, were prepared. By examining the obstacles and shortcomings, this equipment is a development of the previous research by Muhtarom Riyadi and the team, 2015. The specimens, as the sample to test the equipment, were prepared by the ratio of one part of cement and three part of fine aggregate, with the total number of the specimens of 50 pieces.By analyzing the result of observation in trial period, the equipment could function as it should be. The magnitude of maximum tensile strength that causes the mortar specimens to break depends on the quality, age, and tensile area of mortar, which magnitude can be observed in manometer or scale with the unit of kilogram.Keywords: equipment, tensile, mortar, electric motorABSTRAKSifat mekanis mortar keras antara lain kuat tekan, kuat lentur, kuat tarik dan daya lekat. Sementara ini di Laboratorium bahan bangunan Jurusan Teknik Sipil Politeknik Negeri Jakarta untuk uji kuat tarik dan daya lekat mortar belum bisa dilaksanakan karena belum adanya peralatan untuk melakukan pengujian.Penelitian ini bertujuan untuk membuat alat uji tarik mortar menggunakan tenaga penggerak motor listrik guna melengkapi peralatan yang diperlukan di Laboratorium bahan bangunan Jurusan Teknik Sipil Politeknik Negeri Jakarta. Target khusus yang ingin dicapai adalah membuat prototype alat uji tarik mortar.Dalam penelitian ini akan dibuat prototipe alat uji tarik mortar menggunakan tenaga motor listrik dan cetakan benda ujinya, sekaligus untuk menguji kinerjanya. Alat ini merupakan pengembangan oleh peneliti yang terdahulu Muhtarom Riyadi dan anggotanya, 2015), dengan mencermati kendala dan kekurangannya maka penelitian ini merupakan penyempurnaan penelitian sebelumnya Sebagai sampelnya dibuat benda uji tarik mortar dengan perbandingan 1 bagian semen berbanding 3 bagian pasir, sedangkan jumlah benda uji dibuat sebanyak 50 buah.Hasil pengamatan selama uji coba maka alat alat uji tarik mortar menggunakan tenaga penggerak motor listrik dapat berfungsi sebagaimana mestinya. Besarnya gaya tarik maksimum yang menjadikan benda uji tarik mortar putus tergantung dari mutu mortar, umur serta luas penampang tarik yang nilainya dapat diamatai pada manometer atau timbangan berat dengan satuan kilogramKata kunci : Alat, uji, tarik, mortar, motor listrik
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.