Rare earth free alloys are in focus of permanent magnet research since the accessibility of the elements needed for nowadays conventional magnets is limited. Tetragonally strained iron-cobalt (Fe-Co) has attracted large interest as promising candidate due to theoretical calculations. In experiments, however, the applied strain quickly relaxes with increasing film thickness and hampers stabilization of a strong magnetocrystalline anisotropy. In our study we show that already 2 at% of carbon substantially reduce the lattice relaxation leading to the formation of a spontaneously strained phase with 3 % tetragonal distortion. In these strained (Fe 0.4 Co 0.6 ) 0.98 C 0.02 films, a magnetocrystalline anisotropy above 0.4 MJ/m 3 is observed while the large polarization of 2.1 T is maintained. Compared to binary Fe-Co this is a remarkable improvement of the intrinsic magnetic properties. In this paper, we relate our experimental work to theoretical studies of strained Fe-Co-C and find a very good agreement.
GdBa 2 Cu 3 O 7 x -BaHfO 3 (GdBCO-BHO) nanocomposite (NC) films containing 12 mol% BHO nanoparticles were prepared by chemical solution deposition (CSD) following the TFA route on SrTiO 3 (STO) single crystals and buffered metallic tapes supplied by two different companies: Deutsche Nanoschicht GmbH and SuperOx. We optimized the preparation of our GdBCO-BHO solutions with acetylacetone making the film synthesis very robust and reproducible, and obtained 220 nm films with excellent superconducting properties. We show the structural, morphological and superconducting properties of the films after a careful optimization of the processing parameters (growth temperature, oxygen partial pressure and heating ramp). The films reach critical temperatures (T c ) of ∼94 K, self-field critical current densities (J c ) of >7 MA cm 2 and maximum pinning force densities (F p ) of ∼16 GN m 3 at 77 K on STO and T c of ∼94.5 K and J c > 1.5 MA cm 2 on buffered metallic tapes. The transport properties under applied magnetic fields are significantly improved with respect to the pristine GdBCO films. The GdBCO-BHO NC films on STO present epitaxial c-axis orientation with excellent out-of-plane and in-plane texture. The films are, in general, very dense with a low amount of pores and only superficial indentations. On the other hand, we present, for the first time, a systematic study of CSD-grown GdBCO-BHO NC films on buffered metallic tapes. We have used the optimized growth conditions for STO as a reference and identified some limitations on the film synthesis that should be overcome for further improvement of the films' superconducting properties.
Shape memory alloys often show a complex hierarchical morphology in the martensitic state. To understand the formation of this twin-within-twins microstructure, we examine epitaxial Ni-Mn-Ga films as a model system. In-situ scanning electron microscopy experiments show beautiful complex twinning patterns with a number of different mesoscopic twin boundaries and macroscopic twin boundaries between already twinned regions. We explain the appearance and geometry of these patterns by constructing an internally twinned martensitic nucleus, which can take the shape of a diamond or a parallelogram, within the basic phenomenological theory of martensite. These nucleus contains already the seeds of different possible mesoscopic twin boundaries. Nucleation and growth of these nuclei determines the creation of the hierarchical space-filling martensitic microstructure. This is in contrast to previous approaches to explain a hierarchical martensitic microstructure. This new picture of creation and anisotropic, well-oriented growth of twinned martensitic nuclei explains the morphology and exact geometrical features of our experimentally observed twins-within-twins microstructure on the meso-and macroscopic scale.
We report near-infrared-to-visible La2O3:Yb3+,Er3+ (LYE) UC materials with a high internal quantum yield (UCQY) of 3.8%, external UCQY (brightness) of 1.6% and tunable emission color.
High entropy alloys based on the Ta-Nb-Mo-Cr-Ti-Al system are expected to possess high creep and oxidation resistance as well as outstanding specific mechanical properties due to presumed high melting points and low densities. However, we recently reported that arc-melted and subsequently homogenized alloys within this system exhibit a lack of ductility up to 600 °C [H. Chen et al. in Metall.
The global trend of miniaturization and concomitant increase of functionality in microelectronics, microoptics, and various other fields in microtechnology leads to an emerging demand for temperature control at small scales. In this realm, elastocaloric cooling is an interesting alternative to thermoelectrics due to the large latent heat and good down-scaling behavior. Here, we investigate the elastocaloric effect due to a stress-induced phase transformation in binary TiNi and quaternary TiNiCuCo films of 20 μm thickness produced by DC magnetron sputtering. The mesoscale mechanical and thermal performance, as well as the fatigue behavior are studied by uniaxial tensile tests combined with infrared thermography and digital image correlation measurements. Binary films exhibit strong features of fatigue, involving a transition from Lüders-like to homogeneous transformation behavior within three superelastic cycles. Quaternary films, in contrast, show stable Lüders-like transformation without any signs of degradation. The elastocaloric temperature change under adiabatic conditions is −15 K and −12 K for TiNi and TiNiCuCo films, respectively. First-of-its-kind heat pump demonstrators are developed that make use of out-of-plane deflection of film bridges. Owing to their large surface-to-volume ratio, the demonstrators reveal rapid heat transfer. The TiNiCuCo-based devices, for instance, generate a temperature difference of 3.5 K within 13 s. The coefficients of performance of the demonstrators are about 3.
Owing to its ability to produce dense thick-films at room temperature directly from a ceramic powder, the Aerosol Deposition Method (AD) possesses a unique feature in ceramics processing. For this technology, the aerosol generation of particles is a decisive part of reliable process control. However, there has only been a small amount of work published addressing this topic. In this work, we compare the aerosolization and deposition behavior of a fluidized bed generator with an aerosol generator with the rotary brush principle. While film properties very much depend on deposition time for the fluidized bed generator, films produced with the brush generator show a constant film profile, and their film thickness correlates with the controllable aerosol concentration and the duration of deposition. This type of aerosol generation may improve the setup towards a more reliable AD process.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.