Managing household wastewater is an issue that affects hundreds of thousands of people in rural communities nationwide, many of whom rely on septic systems as their primary means of household wastewater disposal. Septic system absorption field products with architectures quite different from traditional pipe-and-gravel systems are being installed in many states with variances from initial design specifications. The objective of this study was to evaluate the performance, as measured by the in-product height of stored solution, of four differing absorption-field product architecture types in a profile-limited soil that was loaded at the maximum allowable rate based on soil morphology. Five chamber, two gravel-less pipe, two polystyrene aggregate, and four pipe-and-gravel systems were installed in a profile-limited, Captina silt loam soil (fine-silty, siliceous, active, mesic Typic Fragiudult) and dosed with raw effluent at rates determined by current State of Arkansas regulations via individual peristaltic pumps. Free-solution monitoring ports were installed within each product, where the depth to free solution was measured periodically and used to evaluate product performance. Data collected from January through August 2009 indicated that preliminary system performance was unaffected by product architecture type. All products performed similarly under dry soil conditions. However, differences among individual products were observed during periods of hydrologic stress (i.e., wet soil conditions). Surfacing of effluent was not observed atop any product, indicating that the current loading rate design method is functioning properly. Preliminary results indicate that some alternative absorption-field products perform similarly to the traditional pipe-and-gravel system, thus providing flexibility and options for homeowners.

On-site wastewater treatment systems (OWTSs) are commonly used by households in areas of low population density to treat household wastewater and recycle it back to the environment. However, new absorption field products of differing architecture types have recently become available. A 3-yr field study was conducted in Bethel Heights, northwest Arkansas to assess several newer architecture types (i.e., chambers, polystyrene-aggregate, and gravel-less pipe) relative to the traditional pipe-and-gravel design under wet- and dry-soil conditions. Thirteen products of four different architecture types were installed in 46-cm-deep trenches in a Captina silt loam (fine-silty, siliceous, active, mesic Typic Fragiudult). Products were evaluated based on in-trench solution storage measured with an electronic water-level sensor approximately weekly from January 2009 through January 2012. Between May 2010 and January 2012, the thickness of any biomat formation was measured approximately weekly by insertion of a wooden dowel through in-trench monitoring ports. Architecture type alone did not affect ( > 0.05) in-trench solution storage. However, solution storage among individual products differed under wet- and dry-soil conditions ( < 0.05). When present, biomat thickness differed significantly ( < 0.05) among all four architecture types, ranging from 1.4 to 6.2 cm thick on average in the pipe-and-aggregate and polystyrene-aggregate types, respectively. Regression analyses showed that biomat thickness increased in three products, did not change in nine products, and decreased in one product over time. Results showed that several currently approved alternative products had similar in-trench solution storage but that several alternative products also had greater solution storage than that of the traditional pipe-and-gravel system. With no observed effluent surfacing, the soil morphology approach appears to be adequate and appropriately environmentally conservative for assigning typical single-family loading rates to alternative OWTS products and to the traditional pipe-and-gravel system.

The SEAMISTTM inverting membrane deployment system has been used successfully at the Mixed Waste Landfill Integrated Demonstration (MWLID) for multipoint vapor sampling, pressure measurement, permeability measurement, sensor integration demonstrations, and borehole lining. Several instruments were deployed inside the SEAMISTTM-lined boreholes to detect metals, radionuclides, moisture, and geologic variations. The liner protected the instruments from contamination, maintained support of the uncased borehole wall, and sealed the total borehole from air circulation. Recent activities included the installation of three multipoint vapor sampling systems * iii MAS Intentionally Left Blank We also wish to acknowledge the DOE Office of Technology Development and the Mixed Waste Landfill Integrated Demonstration for their sponsorship of this project.

No abstract

Approximately 20% of homes nationwide use an on-site treatment system as a form of household wastewater management. However, approximately 10% to 20% of on-site treatment systems malfunction each year, many of which have either failed or exceeded the soil's long-term acceptance rate (LTAR), causing environmental and human health risks. The objective of this field study was to evaluate the effects of soil condition (e.g., wet and dry) and product architecture type A. Gibbons et al.652