No abstract

No abstract

This paper describes a new modular experimental facility that was purpose-built to investigate flow interactions between the combustor and first stage nozzle guide vanes (NGVs) of heavy duty power generation gas turbines with multiple can combustors. The first stage turbine NGV is subjected to the highest thermal loads of all turbine components and therefore consumes a proportionally large amount of cooling air that contributes detrimentally to the stage and cycle efficiency. It has become necessary to devise novel cooling concepts that can substantially reduce the coolant air requirement but still allow the turbine to maintain its aerothermal performance. The present work aims to aid this objective by the design and commissioning of a high-speed linear cascade, which consists of two can combustor transition ducts and four first stage NGVs. This is a modular nonreactive air test platform with engine realistic geometries (gas path and near gas path), cooling system, and boundary conditions (inlet swirl, turbulence level, and boundary layer). The paper presents the various design aspects of the high pressure (HP) blow down type facility, and the initial results from a wide range of aerodynamic and heat transfer measurements under highly engine realistic conditions.

No abstract

No abstract

A new experimental technique for the accurate measurement of steady-state metal temperature surface distributions of modern heavily film-cooled turbine vanes has been developed and is described in this paper. The technique is analogous to the thermal paint test but has been designed for fundamental research. The experimental facility consists of an annular sector cascade of high pressure (HP) turbine vanes from a current production engine. Flow conditioning is achieved by using an annular sector of deswirl vanes downstream of the test section, being both connected by a three-dimensionally contoured duct. As a result, a transonic and periodic flow, highly representative of the engine aerodynamic field, is established: Inlet turbulence levels, mainstream Mach and Reynolds numbers, and coolant-to-mainstream total pressure ratio are matched. Since the fully three-dimensional nozzle guide vane (NGV) geometry is used, the correct radial pressure gradient and secondary flow development are simulated and the cooling flow redistribution is engine-realistic. To allow heat transfer measurements to be performed, a mainstream-to-coolant temperature difference (up to 33.5°C) is generated by using two steel-wire mesh heaters, operated in series. NGV surface metal temperatures are measured (between 20°C and 40°C) by wide-band thermochromic liquid crystals. These are calibrated in situ and on a per-pixel basis against vane surface thermocouples, in a heating process that spans the entire color play and during which the turbine vanes can be assumed to slowly follow a succession of isothermal states. Experimental surface distributions of overall cooling effectiveness are presented in this paper. By employing resin vanes of the same geometry and cooling configuration (to implement adiabatic wall thermal boundary conditions) and the transient liquid crystal technique, surface distributions of external heat transfer coefficient and film cooling effectiveness can be acquired. By combining these measurements with those from the metal vanes, the results can be scaled to engine conditions with a good level of accuracy.

This paper describes the effects of coolant-to-mainstream density ratio and specific heat capacity flux ratio (the product of blowing ratio and specific heat capacity ratio) on the overall cooling effectiveness of high pressure (HP) turbine vanes. Experimental measurements have been conducted at correct engine-matched conditions of Mach number, Reynolds number, turbulence intensity, and coolant-to-mainstream momentum flux ratio. Vanes tested were fully cooled production parts from an engine currently in service. A foreign gas mixture of SF6 and Ar was selected for injection as coolant in the facility so that density and blowing ratios were also matched to the engine situation. The isentropic exponent of the foreign gas mixture coincides with that of air. Full-coverage surface maps of overall cooling effectiveness were acquired by an infrared (IR) thermography technique at a range of mainstream-to-coolant temperature ratios. Measurements were subsequently scaled to engine conditions by employing a new theory based on the principle of superposition and a recovery and redistribution temperature demonstrated in previous papers. It is shown that the two aerodynamically matched situations of air- and foreign-gas-cooled experiments give virtually the same effectiveness trends and patterns. Actual levels differ, however, on account of specific heat capacity flux ratio differences. The effect is described and quantified by a one-dimensional analytical model of the vane wall. Differences in Biot number with respect to engine conditions are discussed as they also influence the scaling of turbine metal temperatures.

A full thermal experimental assessment of a novel dendritic cooling scheme for high-pressure turbine vanes has been conducted and is presented in this paper, including a comparison to the current state-of-the-art cooling arrangement for these components. The dendritic cooling system consists of cooling holes with multiple internal branches that enhance internal heat transfer and reduce the blowing ratio at hole exit. Three sets of measurements are presented, which describe, first, the local internal heat transfer coefficient of these structures and, secondly, the cooling flow capacity requirements and overall cooling effectiveness of a highly engine-representative dendritic geometry. Full-coverage surface maps of overall cooling effectiveness were acquired for both dendritic and baseline vanes in the Annular Sector Heat Transfer Facility, where scaled near-engine conditions of Mach number, Reynolds number, inlet turbulence intensity, and coolant-to-mainstream pressure ratio (or momentum flux ratio) are achieved. Engine hardware was used, with laser-sintered metal counterparts for the novel cooling geometry (their detailed configuration, design, and manufacture are discussed). The dendritic system will be shown to offer improved overall cooling effectiveness at a reduced cooling mass flow rate due to a more uniform film cooling effectiveness, a decreased tendency for films to lift off in regions of low external cross flow, improved through-wall heat transfer and internal cooling efficiency, increased internal wetted surface area of the cooling holes, and the enhanced turbulence induced in them.