The heats of adsorption of two linear CO species adsorbed on the Au degrees particles (denoted L(Au degrees)) and on the Ti(+delta) sites (denoted L(Ti+delta)) of a 1% Au/TiO(2) catalyst are determined as the function of their respective coverage by using the AEIR procedure (adsorption equilibrium infrared spectroscopy) previously developed. Mainly, the evolutions of the IR band area of each adsorbed species (2184 cm(-1) for L(Ti+delta) and at 2110 cm(-1) for L(Au degrees)) as a function of the adsorption temperature T(a), at a constant CO adsorption pressure P(CO), provide the evolutions of the coverages theta(LTi+delta) and theta(LAu degrees ) of each adsorbed CO species with T(a) in isobar conditions that give the individual heats of adsorption. It is shown that they linearly vary from 74 to 47 kJ/mol for L(Au degrees ) and from 50 to 40 kJ/mol for L(Ti+delta) at coverages 0 and 1, respectively. These values are consistent with literature data on model Au particles and TiO(2). In particular, it is shown that the mathematical formalism supporting the AEIR procedure can be applied to literature data on Au-containing solids (single crystals and model particles).

A new simple analytical procedure is described that allows the determination of the heats of adsorption (denoted E(theta)) of adsorbed species at several coverages (theta's) using a single experiment. This procedure is an extension of an original method previously developed (denoted AEIR: adsorption equilibrium infrared spectroscopy). A mass spectrometer is used to determine the amounts of gas (in the present study, CO and H2) either desorbed from or adsorbed on a metal supported catalyst (4.7% Cu/Al2O3 and 2.9% Pt/Al2O3) during the perturbation of the adsorption equilibrium due to a controlled change of the adsorption temperature (Ta) at a quasi-constant adsorption pressure (Pa). These amounts allow us to follow the evolution of the adsorption equilibrium coverage (theta(e)) with Ta at the quasi-constant partial pressure (Pa). Then, the curve theta(e) = f(Ta) provides Etheta = f(theta) with the support of an adsorption model. This procedure presents several advantages as compared to the TPD methods, in particular, considering the theoretical supports linked to the exploitation of the experimental data. As compared to AEIR, the TPAE procedure allows one to study the heats of adsorption of adsorbed species that are not detectable by IR. However, it is not adapted if surface reactions occur in parallel to adsorption/desorption processes.

A silica-supported cobalt catalyst has been developed via incipient wetness impregnation for high-yield synthesis of single-walled carbon nanotubes (SWNTs). Co/SiO2-impregnated catalysts have not been observed to be efficient for SWNT synthesis. Using an appropriately chosen precursor, we show that effective catalysts can be obtained for SWNT synthesis with yields up to 75 wt %. Detailed characterization indicates that the active sites for SWNT synthesis are small cobalt particles resulting from the reduction of a highly dispersed surface cobalt silicate species. The SWNTs produced by this catalyst are of high quality and easy to purify, and the process is simple and scalable.

Highly dispersed cobalt on SBA-15 was successfully prepared by a post synthesis grafting of cobalt. Of the cobalt precursors tested, Co(II) acetylacetonate was found to be the best source for high dispersion of cobalt. The Co-SBA-15 catalysts were characterized with different techniques: N2 physisorption, XRD, TPR, TEM, and X-ray adsorption analysis. The mesoporous structure of SBA-15 was retained after cobalt grafting with up to 10 wt % Co loading. There were no large cobalt oxide particles formed, which indicates all the cobalt ions are highly dispersed on the surface and the direct bonding to the silica surfaces results in a high reduction temperature (1123 K) relative to Co oxides. X-ray absorption analysis demonstrates a local structure of Co ions with all Co ions isolated and bonded with oxygen. XANES analysis requires that the local environment for Co ions be that of either a distorted tetrahedral or an octahedral structure and the fitting of EXAFS data further shows a Co−O bond coordination number of 3.58 ± 0.48, confirming that the Co is in a distorted tetrahedral environment. The catalytic activity of Co-SBA-15 catalyst was studied for the synthesis of carbon single walled nanotubes (SWNT). The high reduction stability of Co-SBA-15 is presumed to make a favorable catalyst for this high temperature reaction. Raman spectroscopy and TEM photographs show that good quality carbon SWNT was synthesized by Co-SBA-15. Moreover, Co-SBA-15 has a higher yield of carbon SWNT compared with Co-MCM-41 (C16 alkyl template) under the same reaction conditions.

No abstract