Electronic skin (e-skin) presents a network of mechanically flexible sensors that can conformally wrap irregular surfaces and spatially map and quantify various stimuli 1-12 . Previous works on e-skin have focused on the optimization of pressure sensors interfaced with an electronic readout, whereas user interfaces based on a human-readable output were not explored. Here, we report the first user-interactive e-skin that not only spatially maps the applied pressure but also provides an instantaneous visual response through a built-in active-matrix organic light-emitting diode display with red, green and blue pixels. In this system, organic light-emitting diodes (OLEDs) are turned on locally where the surface is touched, and the intensity of the emitted light quantifies the magnitude of the applied pressure. This work represents a system-on-plastic 4,13-17 demonstration where three distinct electronic componentsthin-film transistor, pressure sensor and OLED arrays-are monolithically integrated over large areas on a single plastic substrate. The reported e-skin may find a wide range of applications in interactive input/control devices, smart wallpapers, robotics and medical/health monitoring devices.Although both passive 6,8,12 and active-matrix 1,2,5,9 designs can be used for enabling the predicted user-interactive e-skins, the active-matrix design is advantageous as it minimizes signal crosstalk and thereby offers better spatial resolution and contrast, and a faster response. In the active-matrix backplane circuitry, each pixel is controlled by a thin-film transistor (TFT) that acts as a switch for addressing either current-or voltage-driven devices. Here, we incorporate the active-matrix design into the e-skin by using semiconductor-enriched nanotubes 18 as the channel material of the TFTs. Carbon nanotube networks are proven to be a promising material platform for high-performance TFTs (refs 9,17,19-21) with high current drives needed for switching OLEDs (ref. 22). A schematic structure of a pixel of the user-interactive e-skin with an integrated TFT, OLED and pressure sensor is depicted in Fig. 1a. Each pixel in the active-matrix consists of a nanotube TFT with the drain connected to the anode of an OLED. The OLED uses a simple bilayer structure 23 and the colour of the emitted light is controlled by using different emissive layer materials (details in the Methods). In this work, red, green, blue and yellow colours are demonstrated. On top of the OLEDs, a pressure-sensitive rubber 1,5,24,25 (PSR) is laminated, which is in electrical contact with the cathode (that is, top contact) of the OLED at each pixel. The top surface of the PSR is coated with a conductive silver ink to act as the ground contact. Here, the conductivity of the PSR increases by an applied pressure 1,5,24,25 in the underlying OLED turning on. As illustrated in Fig. 1b, the single-pixel circuitry is integrated into an active-matrix array. The resulting system-on-plastic provides a touch user interface, allowing the pressure profile to be...

Preseparated, semiconductive enriched carbon nanotubes hold great potential for thin-film transistors and display applications due to their high mobility, high percentage of semiconductive nanotubes, and room-temperature processing compatibility. Here in this paper, we report our progress on wafer-scale processing of separated nanotube thin-film transistors (SN-TFTs) for display applications, including key technology components such as wafer-scale assembly of high-density, uniform separated nanotube networks, high-yield fabrication of devices with superior performance, and demonstration of organic light-emitting diode (OLED) switching controlled by a SN-TFT. On the basis of separated nanotubes with 95% semiconductive nanotubes, we have achieved solution-based assembly of separated nanotube thin films on complete 3 in. Si/SiO(2) wafers, and further carried out wafer-scale fabrication to produce transistors with high yield (>98%), small sheet resistance ( approximately 25 kOmega/sq), high current density ( approximately 10 microA/microm), and superior mobility ( approximately 52 cm(2) V(-1) s(-1)). Moreover, on/off ratios of >10(4) are achieved in devices with channel length L > 20 microm. In addition, OLED control circuit has been demonstrated with the SN-TFT, and the modulation in the output light intensity exceeds 10(4). Our approach can be easily scaled to large areas and could serve as critical foundation for future nanotube-based display electronics.

Fully printed transistors are a key component of ubiquitous flexible electronics. In this work, the advantages of an inverse gravure printing technique and the solution processing of semiconductor-enriched single-walled carbon nanotubes (SWNTs) are combined to fabricate fully printed thin-film transistors on mechanically flexible substrates. The fully printed transistors are configured in a top-gate device geometry and utilize silver metal electrodes and an inorganic/organic high-κ (~17) gate dielectric. The devices exhibit excellent performance for a fully printed process, with mobility and on/off current ratio of up to ~9 cm(2)/(V s) and 10(5), respectively. Extreme bendability is observed, without measurable change in the electrical performance down to a small radius of curvature of 1 mm. Given the high performance of the transistors, our high-throughput printing process serves as an enabling nanomanufacturing scheme for a wide range of large-area electronic applications based on carbon nanotube networks.

We demonstrate that the silica shell on nanoparticles formed by a typical Stöber method is inhomogeneous in nature. The outer layer of the shell is chemically more robust than the inner layer, which can be selectively etched by hot water. Methods are developed to "harden" the soft silica shells. These new understandings are exploited to develop versatile and template-free approaches for fabricating sophisticated yolk-shell nanostructures.

A protocol for quantum secure direct communication with quantum superdense coding is proposed. It combines the ideas of block transmission, the ping-pong quantum secure direct communication protocol, and quantum superdense coding. It has the advantage of being secure and of high source capacity.

Direct conversion of light into mechanical work, known as the photomechanical effect, is an emerging field of research, largely driven by the development of novel molecular and polymeric material systems. However, the fundamental impediment is that the previously explored materials and structures do not simultaneously offer fast and wavelength-selective response, reversible actuation, low-cost fabrication and large deflection. Here, we demonstrate highly versatile photoactuators, oscillators and motors based on polymer/single-walled carbon nanotube bilayers that meet all the above requirements. By utilizing nanotubes with different chirality distributions, chromatic actuators that are responsive to selected wavelength ranges are achieved. The bilayer structures are further configured as smart 'curtains' and light-driven motors, demonstrating two examples of envisioned applications.

Solution-processed thin-films of semiconducting carbon nanotubes as the channel material for flexible electronics simultaneously offers high performance, low cost, and ambient stability, which significantly outruns the organic semiconductor materials. In this work, we report the use of semiconductor-enriched carbon nanotubes for high-performance integrated circuits on mechanically flexible substrates for digital, analog and radio frequency applications. The as-obtained thin-film transistors (TFTs) exhibit highly uniform device performance with on-current and transconductance up to 15 μA/μm and 4 μS/μm. By performing capacitance-voltage measurements, the gate capacitance of the nanotube TFT is precisely extracted and the corresponding peak effective device mobility is evaluated to be around 50 cm(2)V(-1)s(-1). Using such devices, digital logic gates including inverters, NAND, and NOR gates with superior bending stability have been demonstrated. Moreover, radio frequency measurements show that cutoff frequency of 170 MHz can be achieved in devices with a relatively long channel length of 4 μm, which is sufficient for certain wireless communication applications. This proof-of-concept demonstration indicates that our platform can serve as a foundation for scalable, low-cost, high-performance flexible electronics.

Plant metabolism underpins many traits of ecological and agronomic importance. Plants produce numerous compounds to cope with their environments but the biosynthetic pathways for most of these compounds have not yet been elucidated. To engineer and improve metabolic traits, we need comprehensive and accurate knowledge of the organization and regulation of plant metabolism at the genome scale. Here, we present a computational pipeline to identify metabolic enzymes, pathways, and gene clusters from a sequenced genome. Using this pipeline, we generated metabolic pathway databases for 22 species and identified metabolic gene clusters from 18 species. This unified resource can be used to conduct a wide array of comparative studies of plant metabolism. Using the resource, we discovered a widespread occurrence of metabolic gene clusters in plants: 11,969 clusters from 18 species. The prevalence of metabolic gene clusters offers an intriguing possibility of an untapped source for uncovering new metabolite biosynthesis pathways. For example, more than 1,700 clusters contain enzymes that could generate a specialized metabolite scaffold (signature enzymes) and enzymes that modify the scaffold (tailoring enzymes). In four species with sufficient gene expression data, we identified 43 highly coexpressed clusters that contain signature and tailoring enzymes, of which eight were characterized previously to be functional pathways. Finally, we identified patterns of genome organization that implicate local gene duplication and, to a lesser extent, single gene transposition as having played roles in the evolution of plant metabolic gene clusters.