No abstract

Background: Besides the use of maize grain as food and feed, maize stover can be a profitable by-product for cellulosic ethanol production, whereas the whole plant can be used in silage production. However, yield is reduced by pest damages, where stem corn borers are one of the most important factors limiting yield. Overall, cell wall composition is key in determining the quality of maize biomass, as well as pest resistance. This study aims to address the interrelations between cell wall components in diverse maize genotypes, and pest resistance, ethanolic production and forage digestibility. Results: We can highlight the following results: (i) pests resistant inbred lines may show cell walls with low p-coumaric acid and hemicellulose content; (ii) inbred lines showing cell walls with high cellulose content and diferulate cross-linking may present higher performance in ethanol production; (iii) and inbred lines with enhanced digestibility may have cell walls poor in neutral detergent fibre and diferulates, combined with a lignin polymer composition richer in G subunits. Conclusions: Our results evidence that there is no maize cell wall ideotype among the tested for optimal performance in the three areas evaluated, and maize plants should be specifically bred for each particular application.

Forage feedstock is the greatest source of energy for livestock. Unfortunately, less than 50% of their fiber content is actually digested and assimilated by the ruminant animals. This recalcitrance is mainly due to the high concentration of plant cell wall material and to the limited digestion of the fiber by the microorganisms. A Genome-Wide Association Study (GWAS) was carried out in order to identify Single Nucleotide Polymorphisms (SNPs) associated with forage digestibility traits in a maize Multi-Parent Advanced Generation Intercross (MAGIC) population. We identified seven SNPs, corresponding to five Quantitative Trait Loci (QTL), associated to digestibility of the organic matter, 11 SNPs, clustered in eight QTLs, associated to Neutral Detergent Fiber (NDF) content and eight SNPs corresponding with four QTL associated with Acid Detergent Fiber (ADF). Candidate genes under the QTL for digestibility of the organic matter could be the ones involved in pectin degradation or phenylpropanoid pathway. Transcription factor genes were also proposed for the fiber QTL identified, in addition to genes induced by oxidative stress, or a gene involved in lignin modifications. Nevertheless, for the improvement of the traits under study, and based on the moderate heritability value and low percentage of the phenotypic variability explained by each QTL, a genomic selection strategy using markers evenly distributed across the whole genome is proposed.

Background Besides the use of maize grain as food and feed, maize stover can be a profitable by-product for cellulosic ethanol production, whereas the whole plant can be used for silage production. However, yield is reduced by pest damages, stem corn borers being one of the most important yield constraints. Overall, cell wall composition is key in determining the quality of maize biomass, as well as pest resistance. This study aims to evaluate the composition of the four cell wall fractions (cellulose, hemicellulose, lignin and hydroxycinnamates) in diverse maize genotypes and to understand how this composition influences the resistance to pests, ethanol capacity and digestibility. Results The following results can be highlighted: (i) pests’ resistant materials may show cell walls with low p-coumaric acid and low hemicellulose content; (ii) inbred lines showing cell walls with high cellulose content and high diferulate cross-linking may present higher performance for ethanol production; (iii) and inbreds with enhanced digestibility may have cell walls poor in neutral detergent fibre and diferulates, combined with a lignin polymer composition richer in G subunits. Conclusions Results evidence that there is no maize cell wall ideotype among the tested for optimal performance for various uses, and maize plants should be specifically bred for each particular application.

El objetivo fue evaluar fechas de corte y del uso de aditivos sobre la calidad del ensilado de la planta entera de girasol. La variedad forrajera (Rumbosol-91) se cosechó en las semanas 1, 3 y 5 post-floración (F1, F2 y F3, respectivamente) y tratada con los siguientes aditivos: 1) 1.5 × 105 ufc de inoculante g-1 de forraje, a base de bacterias lácticas homofermentativas Enterococcus faecium, Pediococcus pentosaceus y Lactobacillus plantarum (INOC), 2) 3 ml kg-1 de forraje de una solución al 85% de ácido fórmico (FORM) y 3) sin aditivo (Testigo); siguiendo un diseño factorial 3x3 con cinco repeticiones. La producción de efluente y las pérdidas totales de materia seca (MS) se redujeron, desde 282 y 134 g kg-1 en F+1 hasta 96 y 87 g kg-1 en F+5 como resultado del alto contenido de humedad del forraje próxima a la floración. El análisis NIRS de las muestras de ensilaje mostró que los contenidos de proteína, fibra y digestibilidad descendían significativamente con la madurez de la planta; la rápida acumulación de aceite en la MS hizo que la concentración energética fuese superior en el estado fenológico más avanzado. La calidad fermentativa de los ensilajes fue satisfactoria, independientemente del momento de corte y del uso de aditivo. Se concluye que es preferible el corte de la planta a las cinco semanas post-floración, donde se espera una fermentación aceptable sin necesidad de conservantes.