Cost-effective and reliable damage detection is critical for the utilization of composite materials. This paper presents part of an experimental and analytical survey of candidate methods for in-situ damage detection of composite materials. Experimental results are presented for the application of Lamb wave techniques to quasiisotropic graphite/epoxy test specimens containing representative damage modes, including delamination, transverse ply cracks and through-holes. Linear wave scans were performed on narrow laminated specimens and sandwich beams with various cores by monitoring the transmitted waves with piezoceramic sensors (PZT). Optimal actuator and sensor configurations were devised through experimentation, and various types of driving signals were explored. These experiments provided a procedure capable of easily and accurately determining the time-of-flight of a Lamb wave pulse between an actuator and sensor. Lamb wave techniques provide more information about damage presence and severity than previously tested methods (frequency response techniques), and provide the possibility of determining damage location due to their local response nature. These methods may prove suitable for structural health monitoring applications since they travel long distances and can be applied with conformable piezoelectric actuators and sensors that require little power.
This paper presents an exercise in comparing the performance of microelectromechanical systems (MEMS) actuators and sensors as a function of operating principle. Data have been obtained from the literature for the mechanical performance characteristics of actuators, force sensors and displacement sensors. On-chip and off-chip actuators and sensors are each sub-grouped into families, classes and members according to their principle of operation. The performance of MEMS sharing common operating principles is compared with each other and with equivalent macroscopic devices. The data are used to construct performance maps showing the capability of existing actuators and sensors in terms of maximum force and displacement capability, resolution and frequency. These can also be used as a preliminary design tool, as shown in a case study on the design of an on-chip tensile test machine for materials in thin-film form.
We have developed a classical two- and three-body interaction potential to simulate the hydroxylated, natively oxidized Si surface in contact with water solutions, based on the combination and extension of the Stillinger-Weber potential and of a potential originally developed to simulate SiO(2) polymorphs. The potential parameters are chosen to reproduce the structure, charge distribution, tensile surface stress, and interactions with single water molecules of a natively oxidized Si surface model previously obtained by means of accurate density functional theory simulations. We have applied the potential to the case of hydrophilic silicon wafer bonding at room temperature, revealing maximum room temperature work of adhesion values for natively oxidized and amorphous silica surfaces of 97 and 90 mJm(2), respectively, at a water adsorption coverage of approximately 1 ML. The difference arises from the stronger interaction of the natively oxidized surface with liquid water, resulting in a higher heat of immersion (203 vs 166 mJm(2)), and may be explained in terms of the more pronounced water structuring close to the surface in alternating layers of larger and smaller densities with respect to the liquid bulk. The computed force-displacement bonding curves may be a useful input for cohesive zone models where both the topographic details of the surfaces and the dependence of the attractive force on the initial surface separation and wetting can be taken into account.
Diamond and diamond-like carbon (DLC) thin films possess a number of unique and attractive material properties that are unattainable from Si and other materials. These include high values of Young's modulus, hardness, tensile strength and high thermal conductivity, low thermal expansion coefficient combined with low coefficients of friction and good wear resistance. As a consequence, they are finding increasing applications in micro-electro-mechanical systems (MEMS). This paper reviews these distinctive material properties from an engineering design point of view and highlights the applications of diamond and DLC materials in various MEMS devices. Applications of diamond and DLC films in MEMS are in two categories: surface coatings and structural materials. Thin diamond and DLC layers have been used as coatings mainly to improve the wear and friction of micro-components and to reduce stiction between microstructures and their substrates. The high values of the elastic modulus of diamond and DLC have been exploited in the design of high frequency resonators and comb-drives for communication and sensing applications. Chemically modified surfaces and structures of diamond and DLC films have both been utilized as sensor materials for sensing traces of gases, to detect bio-molecules for biological research and disease diagnosis.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.