The aim of this study was to determine the effect of sandblasting and electrical discharge machining (EDM) on cast and machined titanium surfaces and titanium-porcelain adhesion. Twenty machined titanium specimens were prepared by manufacturer (groups 1 and 2). Thirty specimens were prepared with autopolymerizing acrylic resin. Twenty of these specimens (groups 3 and 4) were cast with commercially pure titanium and the alpha-case layer was removed. For control group (group 5), 10 specimens were cast by using NiCr alloy. Groups 2 and 4 were subjected to EDM while groups 1, 3, and 5 were subjected to sandblasting. Surface examinations were made by using a scanning electron microscope (SEM). A low-fusing porcelain was fused on the titanium surfaces, whereas NiCr specimens were covered using a conventional porcelain. Titanium-porcelain adhesion was characterized by a 3-point bending test. Results were analyzed by Kruskal-Wallis and Mann-Whitney U tests. Metal-porcelain interfaces were characterized by SEM. The bond strength of control group was higher than that of the titanium-porcelain system. There was no significant difference between cast and machined titanium groups (p > 0.05). There was no significant difference between EDM and sandblasting processes (p > 0.05). The use of EDM as surface treatment did not improve titanium-porcelain adhesion compared with sandblasting.

The aim of this study was to determine the effect of airborne-particle abrasion (APA), sodium hydroxide anodization (SHA), and electrical discharge machining (EDM) on cast titanium surfaces and titanium-porcelain adhesion. Ninety titanium specimens were cast with pure titanium and the alpha-case layer was removed. Specimens were randomly divided into three groups. Ten specimens from each group were subjected to APA. SHA was applied to the second subgroups, and the remaining specimens were subjected to the EDM. For the control group, 10 specimens were cast using NiCr alloy and subjected to only APA. Surfaces were examined by using scanning electron microscope and a surface profilometer. Three titanium porcelains were fused on the titanium surfaces, whereas NiCr specimens were covered with conventional porcelain. Titanium-porcelain adhesion was characterized by a 3-point bending test. Statistical analysis showed that the porcelain-metal bond strength of the control group was higher than that of the titanium-porcelain system (p < 0.05). There were no significant differences between the bond strengths of titanium groups (p 0.05), except the bond strengths of Noritake Super Porcelain TI-22 groups on which APA and SHA were applied (p < 0.05). SHA and EDM as surface treatment did not improve titanium-porcelain adhesion when compared to APA.

Hydro mechanical deep drawing (HDD) process is an advanced sheet metal forming technology. The aim of this process is to form deep drawn cups without any kind of forming instability such as buckling, wrinkling or bursting (tearing). The most important parameters in achieving this goal are fluid pressure and blank holder force. So in this study, a fuzzy logic control algorithm was used with Ls-Dyna FEA subroutines to determine the optimum fluid pressure (P) and the blank holder force (BHF) since it requires a lot of time and cost to perform this work with trial and error experiments. Minimum element thickness, punch wall contact position and wrinkling height were used as input parameters in the control algorithm. But studies on determining the BHF with the wrinkling height parameters have not been carried out yet. This will be investigated in further studies.

Hydro-mechanical Deep Drawing (HMD) is an advanced manufacturing process developed to form sheet metal blanks into complex shapes with smooth surfaces using hydraulic pressure as an additional source of deformation force. There are many factors affecting the successful production of desired parts using this manufacturing process. The most important factors are the fluid pressure and blank holder force. Having proper values of these parameters during forming has a direct impact on part properties such as drawing ratio and thinning. In order to determine desired the fluid pressure and blank holder force profiles, which are different for every geometry, material and other process conditions, finite element simulations are conducted to save time and cost. Abaqus FEA software is used in this study. In order to define the continuously changing fluid pressure application area on the sheet material, which is not an available module or standard interface of software, sub-programs (sub-routines) are developed to properly and dynamically define the fluid pressure area. Proper, if not optimal, fluid pressure and blank holder force profiles, which allow the formability (LDR) of sheet material to be maximum, were obtained using trial and error method. Maximum thinning values on metal blank were used as a control parameter to determine if selected loading profiles result in the highest LDR with lowest thinning.

No abstract