The purpose of this study was to analyze the ions released from a surface pre-reacted glass ionomer (S-PRG) filler in distilled water or lactic acid solution. S-PRG filler was mixed with either solution at 1000:1, 100:1, 10:1, and 1:1 ratios by weight. By means of inductively coupled plasma atomic emission spectroscopy and a fluoride electrode, elements released from S-PRG filler were identified to be Al, B, Na, Si, Sr, and F. To investigate the effect of solution pH on ion release, the pH values of the solutions before mixing and after 24 hours' mixing with S-PRG were measured. After 24 hours' mixing, the pH values of solutions at all ratios became more neutral or weakly alkaline regardless of their initial pH levels before mixing. In conclusion, results showed that S-PRG filler released several types of ions, and that ion release was influenced by the mixing ratio of the solution rather than the initial pH of the solution.

No abstract

By measuring the ultrasonic propagation velocity, it can be concluded that CDR application has an ability to promote bovine enamel remineralization.

The purpose of this study was to investigate the effect of previous phosphoric acid etching on the dentin bond strength of single-step self-etch adhesive systems. Facial surfaces of bovine teeth were wet ground with #600 SiC paper. Adhesives were applied with and without previous phosphoric acid etching, and light irradiated. Resin composite was bonded to the adherend surface, followed by light irradiation and storage in water at 37 degrees C. Four groups (n = 10) were made per adhesive system: with and without previous acid etching and with and without thermal cycling between 5 degrees C and 55 degrees C for 10,000 cycles. Specimens were tested in a shear mode at a crosshead speed of 1.0 mm/min. Two-way ANOVA and Tukey HSD test at a level of 0.05 were performed. The changes in dentin bond strengths were different among the adhesive systems tested. In all experimental conditions of this study, the dentin bond strength decreased or remained unchanged with previous acid etching. From the results of this study, previous acid etching might not be acceptable for increasing dentin bond strength of the single-step self-etch adhesive systems.

No abstract

This study investigated the effect of a coating material containing S-PRG fillers on the demineralization of bovine enamel and dentin, by measuring changes in the transmitted ultrasonic velocity. Bovine enamel and dentin specimens with and without coating (n=6 for each condition) were cut into blocks, immersed in 0.1 M lactic-acid buffer solution (pH 4.75) for 10 min twice daily throughout the test period, and stored in a demineralising artificial saliva solution (pH 7.0) between treatments. The propagation time of longitudinal ultrasonic waves was measured by a pulser-receiver with a transducer. Data were evaluated using ANOVA followed by Tukey's HSD test (α=0.05). The sonic velocity decreased over time for specimens stored in demineralising solution; however, coated specimens had a significantly higher sonic velocity than those without coating. The coating material containing pre-reacted glass-ionomer fillers therefore appeared to reduce the demineralisation of enamel and dentin.

The purpose of this study was to investigate the effect of acid erosion on the bonding performance of universal adhesives. Freshly extracted bovine teeth were cut into enamel slabs and assigned to either the Er or the control group. Specimens in the Er group were immersed in citric acid solution (pH 2.1) twice a day and stored in artificial saliva, while control specimens were simply stored in artificial saliva. Differences in the mean values between the control and Er groups were greater than expected, despite accounting for the effect of differences in the adhesive systems (p=0.016). The Er group mainly exhibited cohesive failure in the enamel, while adhesive failure was more frequent in the control group. The sonic velocity was found to decrease over time in the acid attacked specimens. The results indicated that bond strengths of universal adhesive tested increased in eroded enamel.

We used ultrasonic measurements to monitor the influence of power density and primer application on the polymerization reaction of dual-cured resin cements. The ultrasonic equipment comprised a pulser-receiver, transducers, and an oscilloscope. Resin cements were mixed and inserted into a transparent mould, and specimens were placed on the sample stage, onto which the primer, if used, was also applied. Power densities of 0 (no irradiation), 200, or 600 mW cm(-2) were used for curing. The transit time through the cement disk was divided by the specimen thickness to obtain the longitudinal sound velocity. When resin cements were light-irradiated, each curve displayed an initial plateau of approximately 1,500 m s(-1), which rapidly increased to a second plateau of 2,300-2,900 m s(-1). The rate of sound velocity increase was retarded when the cements were light-irradiated at lower power densities, and increased when the primer was applied. The polymerization behaviour of dual-cured resin cements was therefore shown to be affected by the power density of the curing unit and the application of self-etching primer.