This work implicates the synthesis of biochar-hematite nanocomposite from bamboo sawdust and its photodegradation characteristic for remazol brilliant blue. The nanocomposite was prepared through a one-step pyrolysis process in a tubular furnace under a flow of nitrogen and impregnation using FeSO4.7H2O and FeCl3.6H2O. The physicochemical properties were characterized by x-ray diffraction and Fourier transform infrared spectroscopy, which confirmed that hematite was successfully identified on the surface of the nanocomposite. The results also show that the nanocomposite is suitable for photodegradation application. The decolorization of remazol brilliant blue is suitable with the Langmuir isotherm model and pseudo-second-order kinetic model. At pH = 1, initial concentration = 200 mg/L, contact time = 60 minute and nanocomposite dosage 0.4 g/L, the decolorization efficiency reached 96.9%.
This paper presents flexural and tensile properties of sugar palm (Arenga pinnata) fibres-reinforced polyester composites study. The fibres were treated by alkaline solution with 5% NaOH solution for 2 hours of soaking time. The composites were prepared with different orientations of fibres (i.e. 0° + 45°, 0° + 90°, 45° + 90°, and 45° + (-45°)), while the ratio between Arenga pinnata fibres and polyester is 30 percent volume. Hand lay-up method was employed to produce the specimens. ASTM D-790 03 and ASTM D-3039 standard were employed to characterize the specimens in good sequent. As the result, the specimen with 45°+90° orientation generated maximum important values both in flexural strength (24.03 MPa) and modulus (4.01 GPa), tensile strength (23.84 MPa) and modulus elasticity (0.97 GPa). This is due to palm fibres as reinforcement that forms an angle of 90 ° or increasingly upright to the load crossing field (load of bending) and tensile load giving the effect of maximum reinforcement compared to other fibres orientations.
At the smallest scale, hydropower or pico-hydro can be produced by utilizing water flow at the piping system. This paper discusses about the performance of a water bulb-turbine in a water piping water system using the Computational Fluid Dynamic (CFD) method. This study aims to analyze the effect of flow rate and speed on the efficiency of water bulb-turbine using Solidworks Flow Simulation 2016. The propeller turbine design used in this study has 4 blades and a blade angle of 200, and the static bulb using with a ratio of 0.6 to the pipe diameter. The parameter in flow rate applied in this study is between 7 and 13 L/s and for speed parameter between 100 and 1700 rpm. The final result of this study indicates that the efficiency of the water bulb-turbine is a directly proportional increase of flow rate and the highest efficiency reaches at flow rate 13 L/s and 1300 rpm.
The purpose of this study is to synthesize and characterize of iron sand from the south coastal area of Purworejo, Central Java. Iron sand was mechanically filtered using permanent magnets 35 times. The filtered iron sand was characterized using x-ray diffraction (XRD) to determine the compound contained therein and his physical characteristics. The filtered iron sand was heated at temperatures of 800 ° C and 900 ° C for 5 hours in the furnace and after it was cold and followed by XRD testing. Based on the x-ray diffraction pattern, a single phase Fe2 O3 as a permanent magnet base can be formed after a 900 ° C heating process for 5 hours.
Pressure vessel is a container that has been used to contain a pressurized fluids, either oil, gas, or other chemical fluids. It is widely used for the oil, gas and other chemical based industries. Nowadays, finite element analysis is commonly used to reduce the high cost of testing a pressure vessel before manufacturing process. However, further validation is needed to ensure the results of the simulation and safety of the pressure vessels. In this study, theory of distortion energy is used as the tools of validation based on materials properties and behavior. And finally to ascertain wether the pressure vessel is possible for production or a refinement for safety is needed. The results of the study shown that theory of distortion energy can be used as validation tool for finite element analysis on a pressure vessels, however it cannot ensure the safety. Therefore other validation methods are needed to ascertain the safety of the pressure vessel discussed in this report. The cost analysis shown that failure theory combined with other calculation methods can save costs in pressure vessel testing, although some fairly expensive tests cannot be avoided.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.