The objective of this research is to optimize the alkaline treatment variables, including sodium hydroxide (NaOH) concentration, soaking, and drying time, that influence the mechanical behavior of bamboo fiber-reinforced epoxy composites. In this study, a Box–Behnken design (BBD) of the response surface methodology (RSM) was employed to design an experiment to investigate the mercerization effect of bamboo fiber-reinforced epoxy composites. The evaluation of predicted tensile strength as a variable parameter of bamboo fiber (Bambusa vulgaris) reinforced epoxy composite structures was determined using analysis of variance (ANOVA) of the quadratic model. In this study, a total of 17 experiment runs were measured and a significant regression for the coefficient between the variables was obtained. Further, the triangular and square core structures made of treated and untreated bamboo fiber-reinforced epoxy composites were tested under compressive loading. It was found that the optimum mercerization condition lies at 5.81 wt.% of the NaOH, after a soaking time of 3.99 h and a drying time of 72 h. This optimum alkaline treatment once again had a great effect on the structures whereby all the treated composite cores with square and triangular structures impressively outperformed the untreated bamboo structures. The treated triangular core of bamboo reinforced composites gave an outstanding performance compared to the treated and untreated square core composite structures for compressive loading and specific energy absorbing capability.
A natural fiber including kenaf fibers that reinforce with polymeric composite has increased attention in the manufacturing industries. However, the poor adhesion between fiber and matrix are commonly encountered respectively to their compatibility nature namely hydrophilic and hydrophobic. Therefore, alkaline treatment has introduced to reduce the hydrophilic effect of natural fiber. This paper presents the treatment of single kenaf fibers following tensile test and predicted using analysis of variance (ANOVA). Here, the kenaf fibers were modified using NaOH at different solutions. Then, the single kenaf fiber was performed under ASTM D3379-89 standard. The results showed that kenaf fiber which treats with NaOH solution of 6% significantly offered the outstanding performance of the tensile behaviour.
Utilizing agro-waste material such as rice husk (RH) and coco peat (CP) reinforced with thermoplastic resin to produce low-cost green composites is a fascinating discovery. In this study, the effectiveness of these blended biocomposites was evaluated for their physical, mechanical, and thermal properties. Initially, the samples were fabricated by using a combination of melt blend internal mixer and injection molding techniques. Increasing in RH content increased the coupons density. However, it reduced the water vapor kinetics sorption of the biocomposite. Moisture absorption studies disclosed that water uptake was significantly increased with the increase of coco peat (CP) filler. It showed that the mechanical properties, including tensile modulus, flexural modulus, and impact strength of the 15% RH—5% CP reinforced acrylonitrile-butadiene-styrene (ABS), gave the highest value. Results also revealed that all RH/CP filled composites exhibited a brittle fracture manner. Observation on the tensile morphology surfaces by using a scanning electron microscope (SEM) affirmed the above finding to be satisfactory. Therefore, it can be concluded that blend-agriculture waste reinforced ABS biocomposite can be exploited as a biodegradable material for short life engineering application where good mechanical and thermal properties are paramount.
Banana fiber has a high potential for use in fiber composite structures due to its promise as a polymer reinforcement. However, it has poor bonding characteristics with the matrixes due to hydrophobic–hydrophilic incompatibility, inconsistency in blending weight ratio, and fiber length instability. In this study, the optimal conditions for a banana/epoxy composite as determined previously were used to fabricate a sandwich structure where carbon/Kevlar twill plies acted as the skins. The structure was evaluated based on two experimental tests: low-velocity impact and compression after impact (CAI) tests. Here, the synthetic fiber including Kevlar, carbon, and glass sandwich structures were also tested for comparison purposes. In general, the results showed a low peak load and larger damage area in the optimal banana/epoxy structures. The impact damage area, as characterized by the dye penetration, increased with increasing impact energy. The optimal banana composite and synthetic fiber systems were proven to offer a similar residual strength and normalized strength when higher impact energies were applied. Delamination and fracture behavior were dominant in the optimal banana structures subjected to CAI testing. Finally, optimization of the compounding parameters of the optimal banana fibers improved the impact and CAI properties of the structure, making them comparable to those of synthetic sandwich composites.
Biomass is an important renewable energy resource which primarily contributes to heating and cooling end use sectors. It is also a promising alternative source of biofuels to replace the depleting supply of fossil fuels. Surprisingly, few writers have been able to draw on the feedstock significance for oil palm empty fruit bunch (EFB) as the biomass resource for biofuels compared to the other types of biomass waste. Therefore, this paper presents a comprehensive review of EFB as a biomass resource presented in four major parts. First, the introduction covers the demand for bio-oil and describes the different kinds of feedstock, the relevance and potential of EFB biomass. Second, the characteristics of biomass are explained before it is upgraded as biofuel, drawing similarities and contrasts between EFB and other sources of biomass. Pyrolysis processes and reactors used for EFB conversion are described, and the factors affecting the bio-oil yield and quality are discussed. Major reactor parameters are summarized and reactor optimization is discussed. Third, comparison on the properties of the bio-oil vs. petroleum in transportation, power generation, and heating are compared followed by prioritizing the bio-oil properties from the most to least critical, revealing the most promising methods for upgrading. Fourth, the environmental impact, including CO2 emission, of the use of EFB as a promising renewable energy resource and a cleaner alternative fuel is recommended. This paper has comprehensively reviewed the conversion of oil palm empty fruit bunches into biofuels, including the similarities and differences between biomasses, the best reactors, its comparison with fossil fuels, and bio-oil upgrading methods. The upgrading mapping matrix is created to present the best upgrading strategies for the optimum quality of biofuels. This paper serves as a one-stop center for EFB conversion into biofuels.
Lean tools and applications have been adopted globally by many companies and industries such as automotive, aerospace, healthcare, pharmaceutical, shipbuilding, public services, project management and several others. The most basic of lean tools can be distinguished by the following: Value Stream Mapping (VSM), 5S and Kaizen, and many have agreed that these are the best selections in the initial approach of lean system and these techniques are part of the Y Management System (YMS) initiatives. This research is intended to make VSM as the primary working culture, which has been proven suitable to the servicing companies that conduct Maintenance, Repair and Overhaul (MRO) activities. With full cooperation from Company X Sdn. Bhd., researchers were able to review and later harmonize the implementation flow of VSM with the intentions to increase their personnel’s production rate significantly. The rudder repair project involving the maintenance of Royal Military Airforce’s Skyhawk aircraft has been given the opportunity to be experimented with VSM. After the analysis of all 53 personnel involved, it can be concluded that the lean implementation has considerably improved their individual performances, organizational behaviours, future work mapping and personal/team workstations.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.