A detailed understanding of Gasoline Direct Injection (GDI) techniques applied to spark-ignition (SI) engines is necessary as they allow for many technical advantages such as increased power output, higher fuel efficiency and better cold start performances. Within this context, the extensive validation of multi-dimensional models against experimental data is a fundamental task in order to achieve an accurate reproduction of the physical phenomena characterizing the injected fuel spray. In this work, simulations of different Engine Combustion Network (ECN) Spray G conditions were performed with the Lib-ICE code, which is based on the open source OpenFOAM technology, by using a RANS Eulerian-Lagrangian approach to model the ambient gas-fuel spray interaction. Foremost, the main scope of the activity was to identify the most accurate numerical setup in terms of atomization ad secondary break-up models, thanks to a validation of the computed results against experimental data available for the ECN Spray G baseline condition. Specifically, attention was focused on spray penetration along with an analysis of spray morphology and effects of plume-to-plume interaction. Afterwards, the reference setup was tested and validated under different operating conditions, characterized by detailed experimental measurements specifically provided for this work. In particular, Mie scattering and Schlieren techniques allowed the quasi-simultaneous acquisition of both vapor and liquid penetrations, while a customized imageprocessing procedure, developed in Matlab environment, was used for the outline of the spray contours of both fuel phases to measure the parameters characterizing the jet development. A robust reference numerical setup was identified, capable to reproduce with good accuracy the injection process of a multi-hole GDI spray under the wide range of tested operating conditions. COMBINED EXPERIMENTAL AND NUMERICAL INVESTIGATION OF THE ECN SPRAY G
Compression ignition (CI) engines are widely used in modern society, but they are also recognized as a significative source of harmful and human hazard emissions such as particulate matter (PM) and nitrogen oxides (NOx). Moreover, the combustion of fossil fuels is related to the growing amount of greenhouse gas (GHG) emissions, such as carbon dioxide (CO2). Stringent emission regulatory programs, the transition to cleaner and more advanced powertrains and the use of lower carbon fuels are driving forces for the improvement of diesel engines in terms of overall efficiency and engine-out emissions. Ethanol, a light alcohol and lower carbon fuel, is a promising alternative fuel applicable in the dual-fuel (DF) combustion mode to mitigate CO2 and also engine-out PM emissions. In this context, this work aims to assess the maximum fuel substitution ratio (FSR) and the impact on CO2 and PM emissions of different nozzle holes number injectors, 7 and 9, in the DF operating mode. The analysis was conducted within engine working constraints and considered the influence on maximum FSR of calibration parameters, such as combustion phasing, rail pressure, injection pattern and exhaust gas recirculation (EGR). The experimental tests were carried out on a single-cylinder light-duty CI engine with ethanol introduced via port fuel injection (PFI) and direct injection of diesel in two operating points, 1500 and 2000 rpm and at 5 and 8 bar of brake mean effective pressure (BMEP), respectively. Noise and the coefficient of variation in indicated mean effective pressure (COVIMEP) limits have been chosen as practical constraints. In particular, the experimental analysis assesses for each parameter or their combination the highest ethanol fraction that can be injected. To discriminate the effect on ethanol fraction and the combustion process of each parameter, a one-at-a-time-factor approach was used. The results show that, in both operating points, the EGR reduces the maximum ethanol fraction injectable; nevertheless, the ethanol addition leads to outstanding improvement in terms of engine-out PM. The adoption of a 9 hole diesel injector, for lower load, allows reaching a higher fraction of ethanol in all test conditions with an improvement in combustion noise, on average 3 dBA, while near-zero PM emissions and a reduction can be noticed, on the average of 1 g/kWh, and CO2 compared with the fewer nozzle holes case. Increasing the load insensitivity to different holes number was observed.
<div class="section abstract"><div class="htmlview paragraph">In recent years the research on Diesel engines has been increasingly shifting from performance and refinement to ultra-low emissions and efficiency. In fact, the last two attributes are key for the powertrain competitiveness in the propulsion electrified future, especially in the European market where 95gCO<sub>2</sub>/km fleet average and Euro6D RDE Step2 are phasing in at the same time. The present paper describes some of the most innovative research that GM and Istituto Motori Napoli are performing in the field, exploring how the steel-based additive manufacturing can be used to create innovative combustion bowl features that optimize the combustion process to a level that was not compatible with standard manufacturing technologies. In particular, a novel profile combining highly-reentrant sharp-stepped bowl with inner radial-lips has been studied on a 0.5ℓ single-cylinder engine in conjunction to a state of art 2500bar fast-acting fuel injection system, with the objective to demonstrate the full potential of optimized fuel stratification and spray separation enabled by the Radial Mixing Zone (RMZ) concept. The results confirmed the improved fuel/air mixing and more complete combustion promoted by RMZ, that favors PM oxidation. Indeed, after fine-tuning of injector protrusion and spray indexing to the radial lips, excellent reduction of PM by 25-50% vs baseline Euro6B design was recorded, with no detriment to the indicated efficiency nor engine power density. The novel bowl profile was especially effective when compact injection patterns have been applied at part load. This initial study provides a good reference for further improvements that are already under investigation, including durability of the additive manufactured piston with complex geometry.</div></div>
This article introduces an innovative method for the segmentation of Mie-scattering and schlieren images of GDI sprays. The contours of the liquid phase are obtained by segmenting the scattering images of the spray by means of optimal filtering of the image, relying on variational methods, and an original thresholding procedure based on an iterative application of Otsu’s method. The segmentation of schlieren images, to get the contours of the spray vapour phase, is obtained by exploiting the surface curvature of the image to strongly enhance the intensity texture due to the vapour density gradients. This approach allows one to unambiguously discern the whole vapour phase of the spray from the background. Additional information about the spray liquid phase can be obtained by thresholding filtered schlieren images. The potential of this method has been substantiated in the segmentation of schlieren and scattering images of a GDI spray of isooctane. The fuel, heated to 363 K, was injected into nitrogen at a density of 1.12 and 3.5 kg m−3 with temperatures of 333 K and 573 K.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.