structures which exhibit extraordinary behaviour(s). This review represents a comprehensive account of the state-of-the-art in the production of such metamaterials using additive manufacturing methods and highlights areas, which, based on trends observed in the literature, are worthy of further research and require a coordinated effort on behalf of the afore mentioned disciplines in order to advance the state-of-the-art.

The motion of grains in a three-dimensional vibrofluidized granular bed has been measured using the technique of positron emission particle tracking, to provide three-dimensional packing fraction and granular temperature distributions. The mean square fluctuation velocity about the mean was calculated through analysis of the short time mean squared displacement behavior, allowing measurement of the granular temperature at packing fractions of up to eta approximately 0.15. The scaling relationship between the granular temperature, the number of layers of grains, and the base velocity was determined. Deviations between the observed scaling exponents and those predicted by recent theories are attributed to the influence of dissipative grain-sidewall collisions.

Pristine graphene and graphene-based heterostructures can exhibit exceptionally high electron mobility if their surface contains few electron-scattering impurities. Mobility directly influences electrical conductivity and its dependence on the carrier density. But linking these key transport parameters remains a challenging task for both theorists and experimentalists. Here, we report numerical and analytical models of carrier transport in graphene, which reveal a universal connection between graphene’s carrier mobility and the variation of its electrical conductivity with carrier density. Our model of graphene conductivity is based on a convolution of carrier density and its uncertainty, which is verified by numerical solution of the Boltzmann transport equation including the effects of charged impurity scattering and optical phonons on the carrier mobility. This model reproduces, explains, and unifies experimental mobility and conductivity data from a wide range of samples and provides a way to predict a priori all key transport parameters of graphene devices. Our results open a route for controlling the transport properties of graphene by doping and for engineering the properties of 2D materials and heterostructures.

The analogy of vibrofluidized granular beds with a thermal gas of hard discs has been tested. Analysis of the mean squared displacement behavior of the grains allowed comparison of the measured diffusion with the predicted value at a particular combination of granular temperature and packing fraction. High speed photography, image analysis, and particle tracking software enabled accurate location of the grains. Appropriate analysis of the three mean squared displacement regimes, ballistic, diffusive, and crossover between the two extremes, allowed both the diffusion coefficient and the granular temperature to be measured at the same packing fraction. Broad agreement between Chapman-Enskog theory relating temperature to self-diffusion and observation was observed up to packing fractions of ϳ0.7. At higher packing fractions the grains showed evidence of caging and jump diffusion, with the observed diffusion rapidly diverging from that predicted by theory. Measurement of self-diffusion coefficients and subsequent use of kinetic theory was found to be an accurate method to determine the granular temperature for intermediate packing fractions (ϭ0.4-0.6), and would be particularly suitable for those situations where the time resolution of the experimental facility is insufficient to resolve the speed of the grain between collisions.

Fungi have major, negative socioeconomic impacts, but control with bioactive agents is increasingly restricted, while resistance is growing. Here, we describe an alternative fungal control strategy via materials operating passively (i.e., no killing effect). We screened hundreds of (meth)acrylate polymers in high throughput, identifying several that reduce attachment of the human pathogen Candida albicans, the crop pathogen Botrytis cinerea, and other fungi. Specific polymer functional groups were associated with weak attachment. Low fungal colonization materials were not toxic, supporting their passive, anti-attachment utility. We developed a candidate monomer formulation for inkjet-based 3D printing. Printed voice prosthesis components showed up to 100% reduction in C. albicans biofilm versus commercial materials. Furthermore, spray-coated leaf surfaces resisted fungal infection, with no plant toxicity. This is the first high-throughput study of polymer chemistries resisting fungal attachment. These materials are ready for incorporation in products to counteract fungal deterioration of goods, food security, and health.

2D materials have unique structural and electronic properties with potential for transformative device applications. However, such devices are usually bespoke structures made by sequential deposition of exfoliated 2D layers. There is a need for scalable manufacturing techniques capable of producing high‐quality large‐area devices comprising multiple 2D materials. Additive manufacturing with inks containing 2D material flakes is a promising solution. Inkjet‐printed devices incorporating 2D materials have been demonstrated, however there is a need for greater understanding of quantum transport phenomena as well as their structural properties. Experimental and theoretical studies of inkjet‐printed graphene structures are presented. Detailed electrical and structural characterization is reported and explained by comparison with transport modeling that include inter‐flake quantum tunneling transport and percolation dynamics. The results reveal that the electrical properties are strongly influenced by the flakes packing fraction and by complex meandering electron trajectories, which traverse several printed layers. Controlling these trajectories is essential for printing high‐quality devices that exploit the properties of 2D materials. Inkjet‐printed graphene is used to make a field effect transistor and Ohmic contacts on an InSe phototransistor. This is the first time that inkjet‐printed graphene has successfully replaced single layer graphene as a contact material for 2D metal chalcogenides.

No abstract

Prototype drug eluting implants have been 3D printed using a supramolecular polyurethane-PEG formulation. The implants are capable of releasing a pharmaceutical active with effective drug release over a period of up to 8.5 months.