The paper deals with the impact of technological parameters on the heat transfer coefficient and microstructure in AlSi12 alloy using squeeze casting technology. The casting with crystallization under pressure was used, specifically direct squeeze casting method. The goal was to affect crystallization by pressure with a value 100 and 150 MPa. The pressure applied to the melt causes a significant increase of the coefficient of heat transfer between the melt and the mold. There is an increase in heat flow by approximately 50% and the heat transfer coefficient of up to 100-fold, depending on the casting conditions. The change in cooling rate influences the morphology of the silicon particles and intermetallic phases. A change of excluded needles to a rod-shaped geometry with significantly shorter length occurs when used gravity casting method. By using the pressure of 150 MPa during the crystallization process, in the structure can be observed an irregular silica particles, but the size does not exceed 25 microns.
The work deals with technology Patternless process that combines 3 manufacturing process mold by using rapid prototyping technology, conventional sand formation and 3D milling. It's unconventional technology that has been developed to produce large-sized and heavyduty castings weighing up to several tons. It is used mainly in prototype and small batch production, because eliminating production of models. The work deals with the production of blocks for making molds of gypsum and gypsum drying process technology Thermomold. Into blocks, where were made cavities by milling were casted test castings from AlSi10MgMn alloy by gravity casting. At machining of the mold cavity was varied feed rate of tool of cemented carbide. Evaluated was the surface roughness of test castings, that was to 5 micrometers with feed from 900 to 1300 mm/min. The dimensional accuracy of castings was high at feed rate of 1000 and 1500 mm/min did not exceed 0.025 mm.
This paper deals with influencing the crystallisation of Al alloys by a direct squeeze casting method. The effects of changed cooling rates of the casting is evaluated using a heat transfer coefficient at different casting conditions. The experimental results obtained by temperature measurement of the casting and the mould were used to predict the casting and mould surface temperatures using regression curves. The measured temperatures in the sub-surface layers were used to determine the amount of heat transferred from the casting to the mould. The amount of transferred heat increased 20-fold due to the effect of pressure. We also evaluated the effect of the acting pressure on the mechanical properties and microstructure of the alloy used. The process parameters were varied in the experiment.
Submitted article deals with the effect of selected technological parameters on the quality and dimensional accuracy of prototype castings made by Patternless process technology. During experiments were used two types of molding compounds (foamed gypsum and compound based on silica sand and resin). Experiments were focused on optimization of cutting parameters in terms of efficiency, accuracy and possibilities to minimize tool wear. Article deals also with the dimensional and shape accuracy of the castings made by Z-Cast technology. The main aim of the research is to optimize Patternless process technology to such an extent, that achieved dimensional and shape accuracy will be comparable to castings made by the Z-Cast technology.Keywords: silica sand, patternless process, cutting parameters, gypsumArtykuł dotyczy wybranych parametrów technologicznych, które wpływają na jakość i dokładność wymiarową odlewów prototypowych wykonanych technologią bezmodelową. Podczas eksperymentów wykorzystano dwa rodzaje form (spienionego gipsu i mas do formowania na bazie piasku kwarcowego i żywicy). Badania mają na celu optymalizację parametrów cięcia w zakresie wydajności, dokładności i zminimalizowania zużycia narzędzi. Artykuł zajmuje się również dokładnością wymiarów i kształtem odlewów wytwarzanych za pomocą Z-cast. Głównym celem tego badania jest bezmodelowa technika optymalizacji tworzenia do takiego stopnia, aby osiągnąć dokładność wymiarów i kształtu odlewu wytworzonego zpomocą Z-cast.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.