We have previously described the efficient guidance and unidirectional sliding of actin filaments along nanosized tracks with adsorbed heavy meromyosin (HMM; myosin II motor fragment). In those experiments, the tracks were functionalized with trimethylchlorosilane (TMCS) by chemical vapor deposition (CVD) and surrounded by hydrophilic areas. Here we first show, using in vitro motility assays on nonpatterned and micropatterned surfaces, that the quality of HMM function on CVD-TMCS is equivalent to that on standard nitrocellulose substrates. We further examine the influences of physical properties of different surfaces (glass, SiO(2), and TMCS) and chemical properties of the buffer solution on motility. With the presence of methylcellulose in the assay solution, there was HMM-induced actin filament sliding on both glass/SiO(2) and on TMCS, but the velocity was higher on TMCS. This difference in velocity increased with decreasing contact angles of the glass and SiO(2) surfaces in the range of 20-67 degrees (advancing contact angles for water droplets). The corresponding contact angle of CVD-TMCS was 81 degrees. In the absence of methylcellulose, there was high-quality motility on TMCS but no motility on glass/SiO(2). This observation was independent of the contact angle of the glass/SiO(2) surfaces and of HMM incubation concentrations (30-150 microg mL(-)(1)) and ionic strengths of the assay solution (20-50 mM). Complete motility selectivity between TMCS and SiO(2) was observed for both nonpatterned and for micro- and nanopatterned surfaces. Spectrophotometric analysis of HMM depletion during incubation, K/EDTA ATPase measurements, and total internal reflection fluorescence spectroscopy of HMM binding showed only minor differences in HMM surface densities between TMCS and SiO(2)/glass. Thus, the motility contrast between the two surface chemistries seems to be attributable to different modes of HMM binding with the hindrance of actin binding on SiO(2)/glass.

No abstract

Biological molecular motors that are constrained so that function is effectively limited to predefined nanosized tracks may be used as molecular shuttles in nanotechnological applications. For these applications and in high-throughput functional assays (e.g., drug screening), it is important that the motors propel their cytoskeletal filaments unidirectionally along the tracks with a minimal number of escape events. We here analyze the requirements for achieving this for actin filaments that are propelled by myosin II motor fragments (heavy meromyosin; HMM). First, we tested the guidance of HMM-propelled actin filaments along chemically defined borders. Here, trimethylchlorosilane (TMCS)-derivatized areas with high-quality HMM function were surrounded by SiO(2) domains where HMM did not bind actin. Guidance along the TMCS-SiO(2) border was almost 100% for filament approach angles between 0 and 20 degrees but only about 10% at approach angles near 90 degrees . A model (Clemmens, J.; Hess, H.; Lipscomb, R.; Hanein, Y.; Bohringer, K. F.; Matzke, C. M.; Bachand, G. D.; Bunker, B. C.; Vogel, V. Langmuir 2003, 19, 10967-10974) accounted for essential aspects of the data and also correctly predicted a more efficient guidance of actin filaments than previously shown for kinesin-propelled microtubules. Despite the efficient guidance at low approach angles, nanosized (<700 nm wide) TMCS tracks surrounded by SiO(2) were not effective in guiding actin filaments. Neither was there complete guidance along nanosized tracks that were surrounded by topographical barriers (walls and roof partially covering the track) unless there was also chemically based selectivity between the tracks and surroundings. In the latter case, with dually defined tracks, there was close to 100% guidance. A combined experimental and theoretical analysis, using tracks of the latter type, suggested that a track width of less than about 200-300 nm is sufficient at a high HMM surface density to achieve unidirectional sliding of actin filaments. In accord with these results, we demonstrate the long-term trapping of actin filaments on a closed-loop track (width < 250 nm). The results are discussed in relation to lab-on-a-chip applications and nanotechnology-assisted assays of actomyosin function.

No abstract

No abstract

We report on the design and fabrication of a channel structure for high precision guidance and achieving excellent confinement properties for motor-propelled molecular shuttles. The techniques used to manufacture the channel structure are mainly e-beam lithography and selective monolayer functionalization. The structure consists of two lateral layers of concentric channels on a SiO2 surface made biocompatible with the molecular motors. The quality and advantages of the design are demonstrated by experiments using the motor proteins actin and myosin. The special channel geometry leads to stable biochemical conditions with full motor protein functionality. ATP is sufficiently supplied to all parts of the structure by dedicated service channels, as is the venting of ADP and Pi (inorganic phosphorus). Channels of different widths (100–700 nm) and shapes are fabricated and measurements made on them.

Here, we review the use of actin-based motors, (myosins; e.g., the molecular motor of muscle) in nanotechnology. The review starts from the viewpoints of the molecular motors as being important devices responsible of cargo transportation in the cell and end in discussions about their employment in nanotechnological applications. First, we describe basic biophysics of the myosin motors with focus on their involvement in cargo transportation in the living cell, leading us over into a discussion about in vitro motility assays. These are biological test systems where the myosin-induced translocation of actin filaments is studied on an artificial surface outside the cell. Then follows a review about modified motility assays for production of ordered motion. Here, we discuss ours and others' work with regards to making micro-and nanostructured surfaces and channels where the position and direction of movement produced by molecular motors is controlled. In this section, we consider the role of the channel size in promoting unidirectional myosin-induced motion of actin filaments. Furthermore, we consider the usefulness of surface modifications, e.g., various silanization procedures in order to promote and hinder molecular motility, respectively. Particularly, we describe our latest test system being both morphologically and chemically nanostructured giving us unsurpassed possibilities to perform functional studies as well as extremely good spatio-temporal control. Then follows a section about nanotechnological cargo transportation systems based on the actomyosin motor system. For instance, we present results of attaching fluorescent quantum dots as cargoes to the actin filaments. In this section, we also discuss the possibilities of having cargo attachment and detachment being performed on demand. Finally, we consider the usefulness of molecular motors for lab-on-a-chip applications and the requirements for incorporating these motors in commercially viable devices. In this context, the significant potential of the actomyosin motor system to overcome traditional limitations of micro-and nanofluidics is stressed.

No abstract