No abstract

Dissociation of small poly(methyl acrylic acid) (PMAA) anions produced by electrospray was characterized by tandem mass spectrometry. Upon collisional activation, singly, and doubly deprotonated PMAA oligomers were shown to fragment via two major reactions, dehydration and decarboxylation. The elimination of a water molecule would occur between two consecutive acid groups in a charged-remote mechanism, giving rise to cyclic anhydrides, and was shown to proceed as many times as pairs of neutral pendant groups were available. As a result, the number of dehydration steps, together with the abundance of the fragment ions produced after the release of all water molecules, revealed the polymerization degree of the molecule in the particular case of doubly charged oligomers. For singly deprotonated molecules, the exact number of MAA units could be reached from the number of carbon dioxide molecules successively eliminated from the fully dehydrated precursor ions. In contrast to dehydration, decarboxylation reactions would proceed via a charge-induced mechanism. The proposed dissociation mechanisms are consistent with results commonly reported in thermal degradation studies of poly(acrylic acid) resins and were supported by accurate mass measurements. These fragmentation rules were successfully applied to characterize a polymeric impurity detected in the tested PMAA sample. (J Am Soc Mass

Matrix-assisted laser desorption/ionization (MALDI) time-of-flight (TOF) mass spectrometry (MS) is the technique of choice to achieve molecular weight data for synthetic polymers. Because the success of a MALDI-MS analysis critically depends on a proper matrix and cation selection, which in turn relates closely to the polymer chemical nature and size, prior estimation of the polymer size range strongly helps in rationalizing MALDI sample preparation. We recently showed how pulsed gradient spin echo (PGSE) nuclear magnetic resonance could be used as an advantageous alternative to size exclusion chromatography, to rationalize MALDI sample preparation and confidently interpret MALDI mass spectra for homopolymers. Our aim here is to extend this methodology to the demanding case of amphiphilic block copolymers, for which obtaining prior estimates on the Mw values appears as an even more stringent prerequisite. Specifically, by studying poly(ethylene oxide) polystyrene block copolymers of distinct molecular weights and relative block weight fractions, we show how PGSE data can be used to derive the block Mw values. In contrast to homopolymers, such determination requires not only properly recorded calibration curves for each of the polymers constituting the block copolymers but also an appropriate hydrodynamic model to correctly interpret the diffusion data.

No abstract

The dissociation of small poly(methacrylic acid) (PMAA) cations produced by electrospray was characterized by tandem mass spectrometry. Similarly to PMAA ions produced in the negative ion mode, the two electrosprayed cationic forms, namely [PMAA+Na](+) and [PMAA-H+2Na](+), were shown to fragment via a major pathway consisting of successive dehydration steps. Elimination of a water molecule would occur between two consecutive acid groups in a charged-remote mechanism and was shown to proceed as many times as pairs of acidic pendant groups were available. As a result, comparing the number of dehydration steps observed in the MS/MS spectrum of two consecutive oligomers from the polymeric distribution reveals the degree of polymerization of the molecule. Secondary less informative reactions were shown to consist of losses of CO and/or CO(2), depending on the nature of the precursor ion. These fragmentation rules could be used to characterize PMAA-based copolymers, as successfully demonstrated for a polymeric impurity in the tested PMAA sample.

Molecular weight characterization of random amphiphilic copolymers currently represents an analytical challenge. In particular, molecules composed of methacrylic acid (MAA) and methyl methacrylate (MMA) as the repeat units raise issues in commonly used techniques. The present study shows that when random copolymers cannot be properly ionized by MALDI, and hence detected and measured in MS, one possible analytical strategy is to transform them into homopolymers, which are more amenable to this ionization technique. Then, by combining the molecular weight of the so-obtained homopolymers, as measured by MS, with the relative molar proportion of the MMA and MMA units, as given by 1 H NMR spectrum, one can straightforwardly estimate the molecular weight of the initial copolymer. A methylation reaction was performed to transform MAA-MMA copolymer samples into PMMA homopolymers, using trimethylsilyldiazomethane as a derivatization agent. Weight average molecular weight (M w ) parameters of the MAA-MMA copolymers could then be derived from M w values obtained for the methylated MAA-MMA molecules by MALDI, which were also validated by pulsed gradient spin echo (PGSE) NMR. An alkene function in one of the studied copolymer end-groups was also shown to react with the methylation agent, giving rise to MMA-like polymeric by-products characterized by tandem mass spectrometry and which could be avoided by adjusting the amount of the trimethylsilyldiazomethane in the reaction medium. (J Am Soc Mass Spectrom 2010, 21, 1075-1085) © 2010 American Society for Mass Spectrometry P olymers based on weak acids such as poly-(methacrylic acid) (PMAA) have attracted considerable attention because of the ability of the system to change strongly upon variations in the pH and ionic strength of the solution [1]. For example, amphiphilic PMAA-based block copolymers were reported to efficiently adsorb uranyl ions [2] or to selfassemble to produce dynamic micelles sensitive to different stimuli [3][4][5][6]. In particular, block copolymers containing PMAA and poly(methyl methacrylate) (PMMA) segments were the subject of intensive research activities [7][8][9][10]. However, interesting properties were also demonstrated for copolymers containing random MAA-MMA segments [11][12][13][14]. Performance of such materials highly depends on structurally-related parameters but also on molecular weight distribution.Determination of molecular weight parameters is not a trivial task for copolymers. Liquid state nuclear magnetic resonance (NMR) is the most commonly used technique for this purpose but only allows the number average molecular weight (M n ) parameter to be obtained. Size exclusion chromatography (SEC) requires calibration with narrow standards of the same chemical nature and structure as the analyte. Alternatively, one can use calibration which relies on Mark-HouwinkKuhn-Sakurada (MHKS) parameters being known for the standards and the analyte [15], since these parameters depend on both the nature of co-monomers and their relative proportion with...

The complete structural characterization of a copolymer composed of methacrylic acid (MAA) and methyl methacrylate (MMA) units was achieved using tandem mass spectrometry. In a first step, collision-induced dissociation (CID) of sodiated MAA-MMA co-oligomers allowed us to determine the co-monomeric composition, the random nature of the copolymer and the sum of the end-group masses. However, dissociation reactions of MAA-based molecules mainly involve the acidic pendant groups, precluding individual characterization of the end groups. Therefore, methylation of all the acrylic acid moieties was performed to transform the MAA-MMA copolymer into a PMMA homopolymer, for which CID mainly proceeds via backbone cleavages. Using trimethylsilyldiazomethane as a derivatization agent, this methylation reaction was shown to be complete without affecting the end groups. Using fragmentation rules established for PMMA polymers together with accurate mass measurements of the product ions and knowledge of reagents used for the studied copolymer synthesis, a structure could be proposed for both end groups and it was found to be consistent with signals obtained in nuclear magnetic resonance spectra.

No abstract