Ferrite magnetic nanoparticles (MNPs) were functionalized with a variety of silanes bearing different functional endgroups to render them stable with respect to aggregation and keep them well-dispersed in aqueous media. The MNPs were prepared by the thermal decomposition method, widely used for the synthesis of monodisperse nanoparticles with controllable size. This method makes use of a hydrophobic surfactant to passivate the surface, which results in nanoparticles that are solely dispersible in nonpolar solvents. For use in biological applications, these nanoparticles need to be made water-dispersible. Therefore, a new procedure was developed on the basis of the exchange of the hydrophobic surface ligands with silanes bearing different endgroups to decorate ferrite magnetic nanoparticles with diverse functionalities. By this means, we could easily determine the influence of the endgroup on the nanoparticle stability and water-dispersibility. Amino-, carboxylic acid-and poly(ethylene glycol)-terminated silanes were found to render the MNPs highly stable and water-dispersible because of electrostatic and/or steric repulsion. The silane molecules were also found to form a protective layer against mild acid and alkaline environments. The ligand exchange on the nanoparticle surface was thoroughly characterized using SQUID, TEM, XPS, DLS, TGA, FTIR, UV-vis, and zeta potential measurements. The presented approach provides a generic strategy to functionalize magnetic ferrite nanoparticles and to form stable dispersions in aqueous media, which facilitates the use of these magnetic nanoparticles in biological applications.

No abstract

No abstract

Tantalum pentoxide (Ta2O5) is a promising material for the realization of biological interfaces because of its high dielectric constant, its high chemical stability, and its excellent passivating properties. Nevertheless, the deposition of highly organized silane SAMs to realize well-defined and tailored Ta2O5-based (bio)interfaces, has not been studied in great detail as of yet. In this work, we have investigated the formation of a highly ordered, dense monolayer of trichlorosilanes on Ta2O5 surfaces. Specifically, two different cleaning procedures for Ta2O5 were compared and (n-decyl)trichlorosilane (DTS) was used to study the effect of both cleaning methods on the silanization of Ta2O5. Both types of cleaning allowed the formation of complete and crystalline DTS monolayers on Ta2O5, in contrast with the incomplete, disordered silane layer assembled on uncleaned Ta2O5. The deposited self-assembled monolayers were studied by means of contact angle goniometry, Brewster angle FTIR, X-ray photoelectron spectroscopy, cyclic voltammetry, and ellipsometry. Infrared analysis exhibited a highly ordered DTS silane film on Ta2O5 and indicated a larger tilt angle of the alkyl chains on this substrate by comparison to DTS on SiO2. Furthermore, with use of ellipsometry and XPS, the silane film thickness on Ta2O5 was determined to be substantially smaller than that reported in the literature for DTS on SiO2, supporting the observations of an increased tilt angle (approximately 45 degrees ) on Ta2O5 than on SiO2 (approximately 10 degrees ). By means of cyclic voltammetry, the formation of a dense, essentially pinhole-free, silane film was observed on the cleaned samples. In conclusion, the fully characterized and optimized procedure for the silanization of Ta2O5 surfaces with trichlorosilanes will allow the formation of well-defined, reproducible, and controllable chemical interfaces on Ta2O5.

The secret of a successful affinity biosensor partially hides in the chemical interface layer between the transducer system and the biological receptor molecules. Over the past decade, several methodologies for the construction of such interface layers have been developed on the basis of the deposition of self-assembled monolayers (SAMs) of alkanethiols on gold. Moreover, mixed SAMs of polyethylene oxide (PEO) containing thiols have been applied for the immobilization of biological receptors. Despite the intense research in the field of thiol SAMs, relatively little is known about their biosensing properties in correlation with their long-term stability. Especially the impact of the storage conditions on their biosensing characteristics has not been reported before to our knowledge. To address these issues, we prepared mixed PEO SAMs and tested their stability and biosensing performance in several storage conditions, i.e., air, N2, ethanol, phosphate buffer, and H2O. The quality of the SAMs was monitored as a function of time using various characterization techniques such as cyclic voltammetry, contact angle, grazing angle Fourier-transform infrared spectroscopy, and X-ray photoelectron spectroscopy. In addition, the impact of the different storage conditions on the biosensor properties was investigated using surface plasmon resonance. Via the latter technique, the receptor immobilization, the analyte recognition, and the nonspecific binding were extensively studied using the prostate specific antigen as a model system. Our experiments showed that very small structural differences in the SAM can have a great impact in their final biosensing properties. In addition it was shown that the mixed SAMs stored in air or N2 are very stable and retain their biosensor properties for at least 30 days, while ethanol appeared to be the worst storage medium due to partial oxidation of the thiol headgroup. In conclusion, care must be taken to avoid SAM degradation during storage to retain typical SAM characteristics, which is very important for their general use in many proposed applications.