An integrated preparation of safety‐reinforced poly(propylene carbonate)‐based all‐solid polymer electrolyte is shown to be applicable to ambient‐temperature solid polymer lithium batteries. In contrast to pristine poly(ethylene oxide) solid polymer electrolyte, this solid polymer electrolyte exhibits higher ionic conductivity, wider electrochemical window, better mechanical strength, and superior rate performance at 20 °C. Moreover, lithium iron phosphate/lithium cell using such solid polymer electrolyte can charge and discharge even at 120 °C. It is also noted that the solid‐state soft‐package lithium cells assembled with this solid polymer electrolyte can still power a red light‐emitting diode lamp without suffering from internal short‐circuit failures even after cutting off one part of the battery. Considering the aspects mentioned above, the solid polymer electrolyte is eligible for practical lithium battery applications with improved reliability and safety. Just as important, a new perspective that the degree of amorphous state of polymer is also as critical as its low glass transition temperature for the exploration of room temperature solid polymer electrolyte is illustrated. In all, this study opens up a kind of new avenue that could be a milestone to the development of high‐voltage and ambient‐temperature all‐solid‐state polymer electrolytes.
Transition metal-catalyzed substitution of alcohols by N-nucleophiles (or N-alkylation of amines and related compounds with alcohols) avoids the use of alkylating agents by means of borrowing hydrogen (BH) activation of the alcohol substrates. Water is produced as the only by-product, which makes the "BH" processes atom-economic and environmentally benign. Diverse types of homogeneous organometallic and heterogeneous transition metal catalysts, and substrates such as N-nucleophiles including amines, amides, sulfonamides and ammonia, and various alcohols, can be used for this purpose, demonstrating the promising potential of "BH" processes to replace the procedures using traditional alkylating agents in pharmaceutical and chemical industries. Borrowing hydrogen activation of alcohols for C-N bond formation has recently been paid more and more attention, and a lot of new and novel procedures and examples have been documented. This critical review summarizes the recent advances in "BH" substitution of alcohols by N-nucleophiles since 2009. "Semi-BH" N-alkylation processes with or without an external hydrogen acceptor are also briefly presented. Suitable discussion of the "BH" strategy provides new principles for establishing green processes to replace the relevant traditional synthetic methods for C-N bond formation.
In this paper, tris(trimethylsilyl) phosphite (TMSP) and 1,3‐propanediolcyclic sulfate (PCS) are unprecedentedly prescribed as binary functional additives for treating the poor performances of high‐voltage (5 V‐class) LiNi0.5Mn1.5O4/MCMB (graphitic mesocarbon microbeads) Li‐ion batteries at both room temperature and 50 °C. The high‐voltage LiNi0.5Mn1.5O4/MCMB cell with binary functional additives shows a preponderant discharge capacity retention of 79.5% after 500 cycles at 0.5 C rate at room temperature. By increasing the current intensity from 0.2 to 5 C rate, the discharge capacity retention of the high‐voltage cell with binary functional additives is ≈90%, while the counterpart is only ≈55%. By characterizations, it is rationally demonstrated that the binary functional additives decompose and participate in the modification of solid–electrolyte interface layers (both electrodes), which are more conductive, protective, and resistant to electrolyte oxidative/reductive decompositions (accompanying active‐Li+ consuming parasitic reactions) due to synergistic effects. Specifically, the TMSP additive can stabilize LiPF6 salt and scavenge erosive hydrofluoric acid. More encouragingly, at 50 °C, the high‐voltage cell with binary functional additives holds an ultrahigh discharge capacity retention of 79.5% after 200 cycles at 1 C rate. Moreover, a third designed self‐extinguishing flame‐retardant additive of (ethoxy)‐penta‐fluoro‐cyclo‐triphosphazene (PFPN) is introduced for reducing the flammability of the aforementioned binary functional additives containing electrolyte.
A sustainable, heat-resistant and flame-retardant cellulose-based composite nonwoven has been successfully fabricated and explored its potential application for promising separator of high-performance lithium ion battery. It was demonstrated that this flame-retardant cellulose-based composite separator possessed good flame retardancy, superior heat tolerance and proper mechanical strength. As compared to the commercialized polypropylene (PP) separator, such composite separator presented improved electrolyte uptake, better interface stability and enhanced ionic conductivity. In addition, the lithium cobalt oxide (LiCoO2)/graphite cell using this composite separator exhibited better rate capability and cycling retention than that for PP separator owing to its facile ion transport and excellent interfacial compatibility. Furthermore, the lithium iron phosphate (LiFePO4)/lithium cell with such composite separator delivered stable cycling performance and thermal dimensional stability even at an elevated temperature of 120°C. All these fascinating characteristics would boost the application of this composite separator for high-performance lithium ion battery.
Engineering of smart photoactivated nanomaterials for targeted drug delivery systems (DDS) has recently attracted considerable research interest as light enables precise and accurate controlled release of drug molecules in specific diseased cells and/or tissues in a highly spatial and temporal manner. In general, the development of appropriate light‐triggered DDS relies on processes of photolysis, photoisomerization, photo‐cross‐linking/un‐cross‐linking, and photoreduction, which are normally sensitive to ultraviolet (UV) or visible (Vis) light irradiation. Considering the issues of poor tissue penetration and high phototoxicity of these high‐energy photons of UV/Vis light, recently nanocarriers have been developed based on light‐response to low‐energy photon irradiation, in particular for the light wavelengths located in the near infrared (NIR) range. NIR light‐triggered drug release systems are normally achieved by using two‐photon absorption and photon upconversion processes. Herein, recent advances of light‐responsive nanoplatforms for controlled drug release are reviewed, covering the mechanism of light responsive small molecules and polymers, UV and Vis light responsive nanocarriers, and NIR light responsive nanocarriers. NIR‐light triggered drug delivery by two‐photon excitation and upconversion luminescence strategies is also included. In addition, the challenges and future perspectives for the development of light triggered DDS are highlighted.
LiMn2O4-based batteries exhibit severe capacity fading during cycling or storage in LiPF6-based liquid electrolytes, especially at elevated temperatures. Herein, a novel rigid-flexible gel polymer electrolyte is introduced to enhance the cyclability of LiMn2O4/graphite battery at elevated temperature. The polymer electrolyte consists of a robust natural cellulose skeletal incorporated with soft segment poly(ethyl α-cyanoacrylate). The introduction of the cellulose effectively overcomes the drawback of poor mechanical integrity of the gel polymer electrolyte. Density functional theory (DFT) calculation demonstrates that the poly(ethyl α-cyanoacrylate) matrices effectively dissociate the lithium salt to facilitate ionic transport and thus has a higher ionic conductivity at room temperature. Ionic conductivity of the gel polymer electrolyte is 3.3 × 10(-3) S cm(-1) at room temperature. The gel polymer electrolyte remarkably improves the cycling performance of LiMn2O4-based batteries, especially at elevated temperatures. The capacity retention after the 100th cycle is 82% at 55 °C, which is much higher than that of liquid electrolyte (1 M LiPF6 in carbonate solvents). The polymer electrolyte can significantly suppress the dissolution of Mn(2+) from surface of LiMn2O4 because of strong interaction energy of Mn(2+) with PECA, which was investigated by DFT calculation.
Inspired by Taichi, we proposed rigid-flexible coupling concept and herein developed a highly promising solid polymer electrolyte comprised of poly (ethylene oxide), poly (cyano acrylate), lithium bis(oxalate)borate and robust cellulose nonwoven. Our investigation revealed that this new class solid polymer electrolyte possessed comprehensive properties in high mechanical integrity strength, sufficient ionic conductivity (3 × 10−4 S cm−1) at 60°C and improved dimensional thermostability (up to 160°C). In addition, the lithium iron phosphate (LiFePO4)/lithium (Li) cell using such solid polymer electrolyte displayed superior rate capacity (up to 6 C) and stable cycle performance at 80°C. Furthermore, the LiFePO4/Li battery could also operate very well even at an elevated temperature of 160°C, thus improving enhanced safety performance of lithium batteries. The use of this solid polymer electrolyte mitigates the safety risk and widens the operation temperature range of lithium batteries. Thus, this fascinating study demonstrates a proof of concept of the use of rigid-flexible coupling solid polymer electrolyte toward practical lithium battery applications with improved reliability and safety.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.