No abstract

No abstract

The inefficient running of the spark ignition engine at part loads due to the load control method but, mostly, their major weighting in the vehicle's operation time justifies the interest in the technical solutions, which act in this particular operating range. These drawbacks encountered at low part loads are even more amplified when considering larger engines. For instance, it is well known that, at the same engine load, a larger engine is more throttled than a smaller engine; therefore the concerns are the higher pumping work, the lower real compression ratio, and the overall mechanical efficiency, which is also lower. One solution is a reduction in the displacement without affecting the power output. This is what is now commonly known as the downsizing technique.The combination of downsizing and uploading an engine has been known for a long time. However, the conversion, in an acceptable way, of this potential to actual practice is very challenging. On the one hand, the degree of the downsizing is related to the boost pressure. In order to cope with the knocking phenomenon, the downsized high-pressure turbocharged gasoline engine requires a lower volumetric compression ratio that limits the efficiency on part loads. Therefore, the degree of the downsizing has been limited and, thus, the possible fuel consumption reduction has not yet been fully achieved. On the other hand, other problems are encountered when considering a downsized turbocharged gasoline engine: insufficient low-end torque, poor starting performance, and turbo lag.In order to solve these problems an effective combination of the downsized turbocharged gasoline engine with additional technologies is needed. Thus, the paper will present a so-called adaptive thermal engine, which has at the same time a variable compression ratio and a variable intake valve lift. It will then be demonstrated that it is highly suitable for turbocharging, thus resulting in a high downsizing factor.

Nowadays, on average, two thirds of the fuel energy consumed by an engine is wasted through the exhaust gases and the cooling liquid. The recovery of this energy would enable a substantial reduction in fuel consumption. One solution is to integrate a heat recovery system based on a steam Rankine cycle. The key component in such a system is the expander, which has a strong impact on the system’s performance. A survey of different expander technologies leads us to select the reciprocating expander as the most promising one for an automotive application. This paper therefore proposes a steady-state semi-empirical model of the expander device developed under the Engineering Equation Solver (EES) environment. The ambient and mechanical losses as well as internal leakage were taken into account by the model. By exploiting the expander manufacturer’s data, all the parameters of the expander model were identified. The model computes the mass flow rate, the power output delivered and the exhaust enthalpy of the steam. The maximum deviation between predictions and measurement data is 4.7%. A performance study of the expander is carried out and shows that the isentropic efficiency is quite high and increases with the expander rotary speed. The mechanical efficiency depends on mechanical losses which are quite high, approximately 90%. The volumetric efficiency was also evaluated

An experimental and numerical study was performed to investigate the impact of Biodiesel B20 (blends 20% Rapeseed methyl ester with 80 % Diesel volumetric fraction) and different energetic fractions of hydrogen content (between 0 and 5%) on the mixture formation, combustion characteristics, engine performance and pollutant emissions formation. Experiments were carried out on a tractor Diesel engine, four-cylinders, four-stroke, 50 kW/ 2400 rpm, and direct injection. Simulations were conducted using the AVL codes (HYDSIM and BOOST 2013). Simulation results were validated against experimental data, by comparing the inline pressure, needle lift, in-cylinder pressure curves for Biodiesel B20 and pure Diesel fuels at 1400 rpm and 2400 rpm, respectively, under full load operating conditions. Good agreement with a maximum of 2.5% relative deviation on the peak results revealed that overall operation conditions Biodiesel B20 provides lower engine performance, efficiency, and emissions except the NOx which are slightly increased. The Biodiesel B20 has shorter ignition delay. By hydrogen addition to B20 with aspiration of the intake air flow the CO emissions, smoke, and total unburned hydrocarbon emissions THC decreased, while the NOx kept the same increasing trend for 1400 rpm and has not quite apparent trend for 2400 rpm. The enrichment by hydrogen of Diesel and B20 fuels has not a significant effect on ignition delay.