Zirconium phosphates (ZrP) were incorporated into Nafion® 117 membrane by impregnating method to obtain a reduced methanol permeation and improved proton conductivity for fuel cell application. The mechanical properties and water uptake of Nafion® membrane incorporated with zirconium phosphates nanoparticles was more improvement when compared to the commercial Nafion® 117, due to the presence of phosphoric acid within the nanoparticles. The effect of ZrP nano filler on the membrane structural morphology and thermal properties were investigated by Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM). The improved ion conductivity and decreased methanol permeability on the nanocomposite membranes showed a great potential for fuel cell applications. The nanocomposite membrane with high tensile strength was obtained due to the well dispersed zirconium phosphates within the Nafion® matrix.

A series of quaternized poly(2.6 dimethyl‐1.4 phenylene oxide)/polysulfone (QPPO/PSF) blend anion exchange membrane (AEM) were successfully fabricated and characterized for alkaline fuel cell application. Zinc oxide (ZnO) nanoparticles were introduced in the polymer matrix to enhance the intrinsic properties of the AEM. To confirm successful fabrication, Fourier‐transform infrared spectroscopy and nuclear magnetic resonance (1H‐NMR) were used. The membrane properties were enhanced by the addition of ZnO nanoparticles. The addition of ZnO nanoparticles resulted to a higher ion exchange capacity (IEC) of 3.72 mmol g−1, increase of ion conductivity (IC) up to 52.34 mS cm−1 at 80 °C, enhancement of water uptake, and reduced methanol permeability. The QPPO/PSF/2% ZnO composite retained over 80% of its initial IC at room temperature and also retained over 50% of its initial IC at 80 °C when evaluated for alkaline stability. The maximum power output reached for the membrane electrode assembly constructed with QPPO/PSF/2%ZnO was 69 mW cm−2 at room temperature, which is about three times more than the parent QPPO membrane. The above results indicate that QPPO/PSF/ZnO is a good candidate as an AEM for fuel cell application. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45959.

No abstract

No abstract

No abstract

Nafion ® membrane blended with polyacrylonitrile nanofibers decorated with ZrO 2 was successfully fabricated. The composite membrane showed improved proton conductivity, swelling ratio, thermal and mechanical stability, reduced methanol crossover, and enhanced fuel cell efficiency. The nanocomposite membranes achieved a reduced methanol crossover of 5.465 × 10 −8 cm 2 S −1 compared to 9.118 × 10 −7 cm 2 S −1 of recast Nafion ® membrane using a 5 M methanol solution at 80 C. The composite membrane also showed an ion conductivity of 1.84 compared to 0.25 S cm −1 recast Nafion ® at 25 C. The composite membranes showed a peak power density of 68.7 mWÁcm −2 at 25 C, these results show a promising composite membrane for fuel cell application.

Anion exchange membrane fuel cells (AEMFCs) are considered superior to their counterpart proton exchange fuel cells due to their many advantages. Both fuel cells use membranes as polymer electrolytes to improve fuel-cell properties and power output. This work evaluates a series of imidazolium-quaternized poly(2,6-dimethyl-1,4-phenylene oxide) (ImPPO) functionalized zeolitic imidazole framework-8 (ZIF-8) (ImPPO/ZIF-8) as anion exchange membrane (AEM) electrolytes in a direct methanol alkaline fuel cell. FTIR and 1H NMR were used to confirm the successful membrane fabrication. SEM and TGA were used to study the morphological and thermal stability properties of the ImPPO/ZIF-8 membranes. The AEMs obtained in this work had contact angles ranging from 55.27–106.73°, water uptake from 9–83%, ion exchange capacity (IEC) from 1.93–3.15 mmol/g, and ion conductivity (IC) from 1.02–2.43 mS/cm. The best-performing membrane, ImPPO/3%ZIF-8, showed a water uptake of up to 35% at 80 °C, a swelling ratio of 15.1% after 72 h, IEC of 4.06 mmol/g, and IC of 1.96 mS/cm. A power density of 158.10 mW/cm2 was obtained. This makes ZIF-8 a good prospect as a filler for enhancing membrane properties.

No abstract