All-solid-state donor/acceptor planar-heterojunction (PHJ) hybrid solar cells are constructed and their excellent performance measured. The deposition of a thin C60 fullerene or fullerene-derivative (acceptor) layer in vacuum on a CH3 NH3 PbI3 perovskite (donor) layer creates a hybrid PHJ that displays the photovoltaic effect. Such heterojunctions are shown to be suitable for the development of newly structured, hybrid, efficient solar cells.

A preparation technique of TiO2 screen‐printing pastes from commercially‐available powders has been disclosed in order to fabricate the nanocrystalline layers without cracking and peeling‐off over 17 µm thickness for the photoactive electrodes of the dye‐sensitised solar cells. A conversion efficiency of 8·7% was obtained by using a single‐layer of a semi‐transparent‐TiO2 film. A conversion efficiency of 9·2% was obtained by using double‐layers composed of transparent and light‐scattering TiO2 films for a photon‐trapping system. Copyright © 2007 John Wiley & Sons, Ltd.

In pursuit of efficient quantum dot (QD)-sensitized solar cells based on mesoporous TiO(2) photoanodes, a new procedure for preparing selenide (Se(2-)) was developed and used for depositing CdSe QDs in situ over TiO(2) mesopores by the successive ionic layer adsorption and reaction (SILAR) process in ethanol. The sizes and density of CdSe QDs over TiO(2) were controlled by the number of SILAR cycles applied. After some optimization of these QD-sensitized TiO(2) films in regenerative photoelectrochemical cells using a cobalt redox couple [Co(o-phen)(3)(2+/3+)], including addition of a final layer of CdTe, over 4% overall efficiencies were achieved at 100 W/m(2) with about 50% IPCE at its maximum. Light-harvesting properties and transient voltage decay/impedance measurements confirmed that CdTe-terminated CdSe QD cells gave better charge-collection efficiencies and kinetic parameters than corresponding CdSe QD cells. In a preliminary study, a CdSe(Te) QD-sensitized TiO(2) film was combined with an organic hole conductor, spiro-OMeTAD, and shown to exhibit a promising efficiency of 1.6% at 100 W/m(2) in inorganic/organic hybrid all-solid-state cells.

This study successfully demonstrates the application of inorganic p-type nickel oxide (NiOx ) as electrode interlayer for the fabrication of NiOx /CH3 NH3 PbI3 perovskite/PCBM PHJ hybrid solar cells with a respectable solar-to-electrical PCE of 7.8%. The better energy level alignment and improved wetting of the NiOx electrode interlayer significantly enhance the overall photovoltaic performance.

Registro de acceso restringido Este recurso no está disponible en acceso abierto por política de la editorial. No obstante, se puede acceder al texto completo desde la Universitat Jaume I o si el usuario cuenta con suscripción. Registre d'accés restringit Aquest recurs no està disponible en accés obert per política de l'editorial. No obstant això, es pot accedir al text complet des de la Universitat Jaume I o si l'usuari compta amb subscripció. Restricted access item This item isn't open access because of publisher's policy. The full--text version is only available from Jaume I University or if the user has a running suscription to the publisher's contents.

TiO(2) nanotube arrays prepared by electrochemical anodization of Ti foils show impressive light to electricity conversion efficiency in the dye-sensitized solar cells (DSCs). The length of the TiO(2) nanotube arrays (5-14 microm) was controlled by varying the anodization time from 2 to 20 h. The influence of nanotube lengths on the photovoltaic performance of DSCs was investigated by impedance. A flexible DSC using TiO(2) nanotube arrays on a Ti foil as a working electrode and polyethylene naphthalate (ITO/PEN) as counterelectrode in combination with solvent-free ionic liquid electrolyte achieved 3.6% photovoltaic conversion efficiency under simulated AM 1.5 sunlight.

Lead sulfide (PbS) and cadmium sulfide (CdS) quantum dots (QDs) are prepared over mesoporous TiO2 films by a successive ionic layer adsorption and reaction (SILAR) process. These QDs are exploited as a sensitizer in solid‐state solar cells with 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) as a hole conductor. High‐resolution transmission electron microscopy (TEM) images reveal that PbS QDs of around 3 nm in size are distributed homogeneously over the TiO2 surface and are well separated from each other if prepared under common SILAR deposition conditions. The pore size of the TiO2 films and the deposition medium are found to be very critical in determining the overall performance of the solid‐state QD cells. By incorporating promising inorganic QDs (PbS) and an organic hole conductor spiro‐OMeTAD into the solid‐state cells, it is possible to attain an efficiency of over 1% for PbS‐sensitized solid‐state cells after some optimizations. The optimized deposition cycle of the SILAR process for PbS QDs has also been confirmed by transient spectroscopic studies on the hole generation of spiro‐OMeTAD. In addition, it is established that the PbS QD layer plays a role in mediating the interfacial recombination between the spiro‐OMeTAD+ cation and the TiO2 conduction band electron, and that the lifetime of these species can change by around 2 orders of magnitude by varying the number of SILAR cycles used. When a near infrared (NIR)‐absorbing zinc carboxyphthalocyanine dye (TT1) is added on top of the PbS‐sensitized electrode to obtain a panchromatic response, two signals from each component are observed, which results in an improved efficiency. In particular, when a CdS‐sensitized electrode is first prepared, and then co‐sensitized with a squarine dye (SQ1), the resulting color change is clearly an addition of each component and the overall efficiencies are also added in a more synergistic way than those in PbS/TT1‐modified cells because of favorable charge‐transfer energetics.

Colloidal cadmium selenide (CdSe) quantum dots (QDs) have been prepared and exploited as inorganic dyes to sensitize a large-band-gap TiO2 layer for QD-sensitized solar cells. The optimized QD-sensitized solar cells exhibited an unprecedented incident photon-to-charge carrier generation efficiency of 36% and an overall conversion efficiency of over 1.7% at 0.1 sun and 1% at full sun intensity with a cobalt(II/III)-based redox system. The photovoltaic characteristics of CdSe QD-sensitized cells are compared with standard dye-sensitized solar cells, in which the former exhibited about half of the efficiency of the latter. From the kinetics of charge transfer monitored using transient spectroscopic and voltage decay measurements in the CdSe QD-sensitized cell, the regeneration yield of oxidized QDs was found to be close to almost unity, and the electron lifetime was longer in the CdSe QD-sensitized cell than in the dye-sensitized solar cell.